Buy Other Stage & Studio Equipment Products online in Nigeria

Cloud Microphones Cloudlifter Cl - 1 Mic Activator

The Cloud Microphones Cloudlifter CL-1 Mic Activator offers up to +25db of ultra-clean gain, for passive microphones, inline using phantom power. There are certain mics revered for their sound quality. Among them are passive ribbon mics, such as the Royer R121 or MXL R40 , and low-sensitivity dynamic mics, such as the Shure SM7B and the Electro-Voice RE20. But if your preamp doesn't have enough gain or the right impedance requirements, these mics won't perform well. So what do you do if you can't afford a high-end preamp with tons of gain? The Cloud Microphones Cloudlifter CL-1 Mic Activator is the solution. The Cloudlifters address problems due to gain and impedance requirments by giving passive microphone signals a major inline boost, up to +25db of ultra-clean gain, while properly loading the microphones' transformer for transparent operation. The Cloudlifter CL-1 is self contained, driven only by the phantom power from your mixer or preamp. Ideal for dynamics and ribbons alike, the CL-1 turns phantom power into the extra gain required for using passive microphones. The immediate dose of extra gain can make even a budget microphone/preamp combination sound clean and professional. For broadcasting and live sound, the active output signal of the CL-1 can prevent added noise over long cable runs. With endless uses, Cloudlifters are quickly becoming a standard addition to professional, project and home studios.

Audio Mv-bt Bluetooth Input Module

Kali Audio MV-BT Bluetooth Input Module Kali Audio MV-BT Bluetooth Input Module.Kali Audio & rsquo;s MV-BT lets you use your Bluetooth devices with professional speakers, mixers, controllers, and interfaces. Just pair your device by pressing the Kali logo on the front, and use your preferred balanced connector to connect to your system. Ditch the adapters.Kali Audio & rsquo;s MV-BT lets you use your Bluetooth devices with professional speakers, mixers, controllers, and interfaces. Just pair your device by pressing the Kali logo on the front, and use your preferred balanced connector to connect to your system. Features Pairing ButtonPress the Kali logo to pair. LED DisplayBlue light indicates volume level. Weighted KnobEnjoy precise control over the volume level at your fingertips. Volume control is independent, so you can leave volume on your device at full. SpecificationsChannels: 2Inputs: Bluetooth, 3.5mm (AUX)Outputs: 2 x XLR, 2 x TRSHeight: (Shipping) 80mm (84mm)Length: (Shipping) 134mm (138mm)Width: (Shipping) 130mm (154mm)Weight: (Shipping) .5kg (.6kg)In the Box: MV-BT, Local Power Wall Wart

Power Conditioner For Studio Use - Ac-210a E

Furman - Power Conditioner - Ac-210a E The AC-210AE compact power conditioner features Furman & rsquo;s revolutionary SMP technology. Furman & rsquo;s Series Multi-Stage Protection (SMP) circuit features our exclusive Linear Filter Technology (LiFT) and Extreme Voltage Shutdown (EVS). Together, these technologies comprise what is, without question, the world & rsquo;s most advanced and comprehensive transient voltage surge suppressor. SMP (Series Multi-Stage Protection Plus) Furman & rsquo;s SMP surge suppression virtually eliminates service calls. Traditional surge suppression circuits sacrifice themselves when exposed to multiple transient voltage spikes, requiring the dismantling of your system, and repair of your surge suppressor. Not so with SMP. With Furman & rsquo;s SMP, damaging transient voltages are safely absorbed, clamped and dissipated & ndash; no sacrificed parts, no service calls, no down time. Unique to Furman & rsquo;s SMP is its unparalleled clamping voltage, even when tested beyond the grueling specifications of & ndash; USA/CIDA & rsquo;s A-1-1 test. While other designs offer clamping voltages that are well above 300VAC peak (far beyond long accepted professional standards), Furman & rsquo;s SMP clamps at 376VAC peak, 275 VAC RMS even when tested with multiple 6000VAC & ndash; 3000 Amp surges! This unprecedented level of protection is only available with Furman & rsquo;s SMP technology. LiFT (Linear Filtering Technology) Unfortunately, traditional AC filter/conditioners have been designed for unrealistic laboratory conditions. Prior technologies could actually harm audio and video performance more than they help, due to the resonant peaking of their antiquated, non-linear designs. Under certain conditions, these designs can actually add more than 10 dB of noise to the incoming AC line! Worse still, lost digital data, the need to reboot digital presets, or destroyed digital converters are frequently caused by excessive voltage spikes and AC noise contaminating the equipment ground. Furman & rsquo;s SMP with LiFT takes another approach, ensuring optimal performance through linear filtering and no leakage to ground. E.V.S. (Extreme Voltage Shutdown) Furman & rsquo;s trusted overvoltage circuitry protects against all too frequent accidental connections to extreme voltage by shutting off the incoming power until the overvoltage condition is corrected. Compact Chassis Design At only 1.75 & rsquo;H x 5 & rsquo;W x 8.5 & rsquo;D, and weighing in at only 3 lbs., the AC-210 A E & rsquo;s compact, low-profile design makes it ideal for mounting to the back of a flat-screen television, or anywhere that discretely located, remote power protection and purification are needed.

Arturia Microfreak Experimental Hybrid Synthesizer

Arturia MicroFreak EXPERIMENTAL HYBRID SYNTH A synthesizer like no other, MicroFreak is a peculiar, exceptional instrument that rewards the curious musician. It blends wavetable and digital oscillators with analog filters. It features a unique poly-aftertouch flat keyboard. It adds controlled randomness to sequences. This isn & rsquo;t a revolution, it & rsquo;s a mutiny. Whether you & rsquo;re looking for your first, affordable hardware synth or are a collector looking for original sounds and unique interface, MicroFreak is the synth you need. Small but fierce MicroFreak packs so much in to such a compact instrument, you & rsquo;ll wonder how we did it. We & rsquo;d love to say it was magic, but it was pure skill and passion. The best of both worlds Even though MicroFreak has a digital oscillator at its heart, & ldquo;opposites attract & rdquo; as the saying goes. That & rsquo;s why we & rsquo;ve included a lush-sounding analog filter. A digital synth like no other, Arturia MicroFreak is a peculiar, exceptional instrument that rewards the curious musician. It blends wavetable and digital oscillators with analog filters. It features a unique poly-aftertouch flat keyboard. It adds controlled randomness to sequences. This isn't a revolution, it's a mutiny. Wavetable and digital oscillators Collaboration with Mutable Instruments Huge variety of sound possibilities Analog filters Arpeggiator and sequencer Poly-aftertouch flat keyboard Crystal-clear OLED screen 5 & times;7 modulation matrix Paraphonic mode Use MicroFreak as a controller to experience polyphonic aftertouch Un Grain de Folie / a touch of madnessThis out-there little music machine features a versatile digital oscillator so you can create rare and interesting sounds with ease. Modes like Texturer, KarplusStrong, Harmonic OSC, and Superwave give adventurous musicians the chance to explore totally new, unheard possibilities. Like having dozens of synths in just one instrument, both wild-eyed newcomers and seasoned professionals will fall in love with MicroFreak's flexible, powerful synth engine. We're in this togetherWhile it can be fun to play by yourself, things get more exciting when there's two. Arturia loves to collaborate, and MicroFreak is the first collaboration between Arturia and acclaimed modular synth pioneers Mutable Instruments. Among the multiple modes of MicroFreak's synth engine you'll be able to select the much-loved Mutable Instruments Plaits oscillator and with added paraphony. Now you can enjoy the same otherworldly sounds, the same modes and the same parameter controls as the iconic Plaits eurorack module, but from a self-contained, performance-ready hardware synth. The best of both worldsInspired by the trailblazing 12dB Oberheim SEM filter, you can make MicroFreak's filter scream or whisper to taste. The filter is state-variable and can even self-oscillate. You can use this is any way you like, from taking the edge off the razor-sharp wavetable sounds to automating the cutoff by modulating it with keyboard pressure or the built-in sequencer. Taste the spice, throw the diceWait, did we mention that MicroFreak has a sequencer? And a mod matrix? Things are about to get seriously interesting! Record up to four automations, edit notes per step or use the innovative Spice and Dice sequencer functions to find happy accidents. Add randomization to create evolving, original patterns and virtually rewire and reconfigure its signal chain and controls with the 5 & times;7 modulation matrix. 'That's a funny looking keyboard'That's right, it is. It isn't really even a keyboard; it's a PCB, super-flat, with no moving parts. Will it track lightning-fast synth solos? You bet & ndash; better than a traditional keyboard, actually. Will it let you be expressive? Of course: it's not only pressure-sensitive but also offers poly-aftertouch. This means each key can control parameters in a different way depending on how much you touch. You can also use its USB, MIDI and CV outputs to control instruments in your DAW and modular synths. This also means that you can also use MicroFreak as a controller to experience polyphonic aftertouch with cutting edge software instruments. DOWNLOAD:

Dp48 Channel Personal Monitor Mixer

Midas DP48 Dual 48 Channel Personal Monitor Mixer The Midas DP48 is a dual 48 channel personal monitor mixer that allows 2 performers to fully control their monitor mixes and hear exactly what they want and even record and playback rehearsals and performances. With a simple and intuitive interface and the ability to connect to any AES50-equipped device, the DP48 can create a complete monitoring system perfect for use in the studio or on stage. The DP48 gives performers complete control over their monitor mix with 12 stereo groups for quickly creating and balancing mixes. All 48 channels of the DP48 can be mixed within these 12 groups and can handle any kind of monitor set up. Vocalists, for example can place the vocal channel in Group 1 while the drums, bass and guitar channels can be placed in Groups 2,3 and 4 respectively. Drummers who may be more particular can create more complex mixes with the DP48; separately mix their kick, snare and hi hat in Groups 1-3 with the two overhead mics panned left and right in Group 4. The dual mix feature even allows two users to be connected to one DP48 each with their own separate stereo group mix. There are three dedicated controls for each of the Mix A and B outputs, providing independent adjustments for the respective Output Volume, the selected Group Level and for the assignable My Group Level. Both Main Mixes feature separate EQ, Reverb Level and Limiter settings & mdash;especially useful when both talents are using different in-ear or over-ear headphones. Every gigging musician has had this experience: you & rsquo;re already into your set, but you can barely hear yourself. You try to communicate to the front of house engineer with some sophisticated hand signals, but he & rsquo;s not picking up what you & rsquo;re putting down. So, you shout, & ldquo;Hey, can I get a little more of me in the mix? & rdquo; At Music Bliss, we know nothing breaks the flow of a performance faster. But now, with the Midas DP48, you & rsquo;ll never have to go through that again. A 48-channel mixer with 12-stereo groups and a clean, easy-to-use interface, the DP48 has everything you need to take total control over your personal monitor mix. Hook it up to a stage wedge or feed your in-ear monitors. And if you & rsquo;re using IEMs, you can dial in a touch of ambiance with the DP48 & rsquo;s built-in microphone, so you don & rsquo;t feel separate from the audience and the other performers. Using a Cat 5e cable, the DP48 easily connects to any AES50-equipped digital console and can be remotely powered over the ethernet cable or with a separate power supply. Take control of your monitoring Your monitor mixes are personal to you. And with the Midas DP48, they're under your control. This handy personal monitor mixer lets you hear exactly what you want to, as well as being able to record and playback performances. You can take advantage of 12 stereo groups, allowing you to create and balance monitor mixes quickly and easily. Each and every channel on the DP48 can be mixed within the groups, enabling you to create tailored mixes for any situation. Dual mix capabilities Need more than one mix from your DP48? No problem. Two people can connect to a single DP48, and each can have their own dedicated stereo group mix. The outputs for Mix A and Mix B each feature the three controls for adjusting the Output Volume, selected Group Level, and My Group Level. You can also take advantage of separate EQ, Reverb Level, and Limiter settings for each main mix. Flexible and intuitive It's easy to make your mixes your own. Each of the D48's groups boasts a dedicated 3-band EQ, compressor, and reverb. All of which can be adjusted with ease using a single control knob. All you have to do is press a button, and you can change the parameter using the SELECT/EDIT knob. You can boost or attenuate lows, mids, and highs, whilst the compressor setting lets you tame dynamics whilst controlling the peak limiting threshold for Mix A or Mix B. You can add atmosphere and spatial ambience with the built-in studio-quality reverb, which is applied independently from the main console. Plus, a handy Pan button lets you adjust the stereo field of your selected group with ease. Intelligent integrated features The DP48 is more than just a monitor mixer. With a built-in SD card slot, you can easily record rehearsals or performances directly from your DP48. You can then play these recorded mixes back to either Mix A or Mix B. When recording, you can take advantage of the mix-minus function, which allows you to remove respective My Group signals to use as a backing track when practising. Plus, you can even store your favourite mixing presets to the SD card and load them up quickly and easily if you happen to be using a different DP48. But that's not all. The DP48 takes away the feeling of isolation that IEMs can often leave you with. A handy built in ambience microphone lets you hear more of the room and stage around you, so you can communicate with other performers or your audience with ease. There's even an automatic ducking function that reduces the level of the mic when you're playing, so you can keep your mix clear for hassle-free monitoring. AES50 connectivity Power your DP48 over ethernet. With a direct AES50 connection to a device such as the Midas HUB4, you can run your DP48 without the need for an external power supply. Most 44.1/48kHz AES50 devices will work, including Midas and Behringer digital consoles and I/O boxes (Power over Ethernet functionality on other device required). There are also AES50 return channels. These allow you to send your personal mixes from your DP48 back to your console or hub, allowing you to connect to wireless IEM transmitters. Plus, input channel labelling and colour information can be transferred to your mixer via AES50. What's more, when connecting to a Midas hub, setup and control can be done remotely from your mixer. In the box Midas DP48 External Power Supply Quick Start Guide Features Dual 48-channel personal monitor mixer Compatible with Midas personal monitoring system hubs 12 stereo groups for rapid creation and balancing of personal mixes from fully configurable stem groups Dual mix feature allows independent control of two complete monitor mixes Integrated SD card interface for stereo recording and playback of rehearsal sessions and performances Built-in stereo ambience microphone provides on-stage sound feed to remove the sense of isolation with IEMs Studio-quality reverb adds spatial ambience to personal in-ear mixes, independent from the main console Remotely powered via direct AES50 connection from Midas hubs featuring Power over Ethernet Compatible with any 44.1/48kHz AES50-equipped devices including Midas and Behringer digital consoles and I/O boxes Midas PRO SERIES and M32 console input channel labelling and colour information transmitted to the DP48 via AES50 input channels AES50 return channels allow personal mixes to be sent back to the console or hub for connection to wireless IEM transmitters Remote operation up to 100-metres via screened CAT5/5e cable Remote setup and control of the DP48 via Midas hubs Full remote control of another DP48 when both are connected to the same hub or are used in a daisy chain configuration High-contrast 2.4'' colour TFT display provides a clear overview of mix parameters, meters, and group assignments Analogue stereo auxiliary input for local click track High power headphone output for use in all stage monitoring environments Fully adjustable limiter allows for safe monitoring levels within sound exposure limits Mounts securely on a microphone stand using the DP48MB adapter (available separately) Designed and engineered in the UK Covered by Midas' 10-year warranty program Specifications Connectors: Headphones Mix A/B: 2 x 1/4'' TRS, stereo, unbalanced, 25 Ohms Line Mix A/B: 2 x 1/4'' TRS, mono, balanced, 1 k Ohm / 2 x 1/4'' TRS, mono, unbalanced, 500 Ohms Aux In: 2 x 1/4'' TRS, unbalanced, 20 k Ohms / 2 x 1/4'' TRS, balanced, 40 k Ohms AES50 Thru/In: 2 x RJ45 Low EQ: +/-15dB, semi-parametric, low shelving Mid EQ: +/-15dB, semi-parametric, peaking High EQ: +/-15dB, semi-parametric, high shelving EQ Frequency: 20hz to 22kHz, adjustable Limiter: Ratio & infin;:1 Maximum Level: +12.8dBu (headphones) Mix A/Mix B: 2 x stereo AES50: Audio Channels at 48kHz: 48 Sample Rate: 44.1/48kHz Sample Word Length: 24-bit Clock Synchronisation: AES50 IN Latency: Min. 70 & micro;s per node (AES50) Cable: Ethernet CAT 5e Maximum Cable Length: 100m SD/SDHC Format: FAT32 Card Memory: Up to 32GB supported Power Supply: AES50 Input: PoE (IEEE802.3af) Mains Connection: External power supply, 24VDC/600mA (included) Power Consumption: Max. 14W (with DC adaptor) Dimensions: 69mm x 242mm x 164mm / 2.72'' x 9.53'' x 6.46'' (H x W x D) Weight: 1.3kg / 2.9lbs Product Code: DP48

Dl231 24×24 Active Microphone Splitter With 2 Preamps Per Input

Midas DL231 24 & times;24 Active Microphone Splitter with 2 Preamps per Input The DL231 is an Active Microphone Splitter from Midas with 24 inputs and 24 outputs. With two independent Midas microphone preamplifiers per input channel with switchable 48V phantom power. This microphone splitter features a PCB layout specifically designed to maintain grounding as well as separation for both analog and digital signals. It comes fitted with an Ethernet control port and four AES50 ports for dual-redundant handling of two independent digital audio interfaces. MIDI in, out, and thru ports are also on board for use with Midas consoles. 24 Input, 24 Output Active Microphone Splitter with 2 Independent Midas Microphone Preamplifiers per Input 2 award-winning Midas microphone preamplifiers per input with switchable +48 V phantom power 2 dual redundant AES50 network ports with independent phase-locked loop synchronisation 24 electronically balanced output channels can be sourced from microphone preamplifiers or AES50 ports Remote operation up to 100 m via CAT5/5e cable Selectable 96 kHz or 48 kHz sample rate operation All settings programmable from front panel controls or console PSU status indicator LEDs and configuration LCD display on front panel MIDI In, Out and Thru connectors Features Neutrik etherCON* AES50 network ports Rugged 5U rackmount chassis for durability in portable applications Dual redundant auto-ranging universal switch-mode power supplies

Presonus Nsb 8.8 – 8×8 Avb-networked Stage Box

Designed to work seamlessly with PreSonus StudioLive Series III mixers, the PreSonus NSB 8.8 stage box offers 8 locking combo mic/line inputs with remote-controlled XMAX preamps that include gain compensation for shared input scenarios, as well as 16 direct inputs via AVB. All inputs can be controlled from a StudioLive Series III console and from free PreSonus UC Surface software. All eight outputs employ locking XLR jacks, while the built-in 2-port AVB switch lets you daisy-chain multiple units. The rugged steel chassis with sturdy handles is designed with a stage box form factor and allows the NSB 8.8 to sit well on the stage and survive the rigors of on-the-road wear and tear. The unit can be rackmounted with an optional rack-ear kit. Analog Input/Output Locking, remote controllable combo mic/line inputs 8 remote-controllable XMAX preamps Gain compensation for shared inputs 8 locking XLR line outputs Meters, Controls, and Processing Mute All button +48V indicators Easy setup and control from StudioLive Series III consoles and UC Surface Digital 16x8 AVB (8 direct input channels + 8 gain-compensated input channels) 2 AVB ports with locking XLR Ethernet jacks Actively Integrated Software Easy setup and control from PreSonus UC Surface touch control software for Mac, Windows, iPad, and Android, available free from Apple App Store and Google Play Power Locking IEC power jack Physical Rugged stage box enclosure Optional rack ears Compatible with stage pockets from Ace Backstage

Presonus Studio 68c Audio Box

PreSonus Studio 68c Audio box & ndash; Sound Card for Music Production Studio 68c: Powerful, Flexible Production Tools Powerful, flexible production tools. Amazing sound quality with four of PreSonus & rsquo; famed XMAX analog mic preamps, plus professional metering and monitoring features make the Studio 68c ideal for small productions, electronic artists, and bands looking to take charge of their recordings. Two stereo outputs provide flexible output options. A powerful headphone amp with A/B switching lets you listen in to either mix, ideal for live performance applications. With a license included with registration, the Studio 68c is an audio production powerhouse right out of the box. An excellent choice for small bands, producers, and small and mid-sized studios, the Studio 68c 6-in, 6-out, USB-C & trade; compatible audio interface records at up to 192 kHz. You get two mic/line/instrument and two mic/line inputs, all with PreSonus & reg; XMAX mic preamps, plus DC-coupled line outputs and MIDI I/O. A complete, all-in-one recording studio, the Studio 68c comes with PreSonus & rsquo; award-winning Studio One & reg; Artist music production software for macOS & reg; and Windows & reg; and is backward compatible with USB 2.0 and 3.0 connections. The Audio Interface that does more Studio 68c: The versatile, Ultra-high-def USB-C Compatible Audio Interface. World-class recording software included. Seamlessly integrated with the included PreSonus Studio One Artist music production software, the Studio 68c interface works with virtually all macOS and Windows recording software. The 6-in, 6-out Studio 68c audio interface features USB-C & trade; compatible computer connectivity and includes 2 combo mic/instrument/line inputs and 2 combo mic/line inputs with +48V phantom power for condenser mics, plus S/PDIF digital I/O. All four & frac14;-inch TRS, line-level outputs are DC coupled, enabling them to send control voltages. Superior sound. The Studio 68c operates at up to 192 kHz for ultra-high-definition recording and mixing. High-quality converters on every input and output and four of PreSonus & rsquo; professional-grade XMAX mic preamps enable you to capture complex musical harmonics smoothly and naturally, with no audible distortion. XMAX mic preamps are known the world over for their ability to deliver incredibly high headroom, deep lows, smooth highs, and a rich overall sound so you & rsquo;ll hear every breath, transient, and detail in your recordings. Stress-free recording. Professional tools make any job easier. That & rsquo;s why we included professional input and output metering on the Studio 68c, allowing you to keep an eye on your input and mix levels when you & rsquo;re recording by yourself. An easy-to-use direct monitor control blends the analog input signals with playback from your computer, simplifying monitoring. Two pairs of outputs afford two different stereo mixes. Plus, all four & frac14;-inch TRS, line-level outputs are DC coupled, enabling them to send control voltages. The Cue A/B button allows you to toggle between each mix while listening in on headphones, great for live performance and studio alike. Wherever the sound takes you. When you & rsquo;re upgrading your performance rig or building a custom production studio, Studio 68c will give you clear, clean, ultra-high-def sound with the professional tools you need to achieve world-class results. While it & rsquo;s a perfect companion for any recording software, Studio 68c and included Studio One Artist provide you with a complete, affordable recording solution that will make you sound great.

Presonus Broadcast Accessory Pack

A perfect complement to the M7, Relevator, PX-1, PD-70, and similar microphones, the Presonus Broadcast Accessory Pack gives you essential items to get the most out of your mic in a broadcast-style studio. The kit comprises a desktop boom arm, a pop filter, an XLR cable and a pair of HD7 headphones for monitoring. This pack is perfect for podcasters, streamers, and anyone creating content in their home studio. With all the accessories in tow, your broadcast recording experience will be more convenient and will sound better to boot. All-In-One Solution Get the most from your microphone with The Broadcast Accessory Pack, as it comprises everything podcasters, live streamers, gamers, and YouTubers need to level up their online presence in a convenient bundle. PBA-1 Boom Arm The rugged PBA-1 boom arm is suitable for use with Revelator, PX-1, PD-70, or nearly any mic you prefer. It gets your mic up off of your desk, freeing up valuable tabletop space while providing better positioning options. APF-1 Pop Filter An APF-1 pop filter is also included to help reduce the plosive sounds that can occur when recording loud vocalists or employing close mic positioning. HD7 Headphones The lightweight HD7 headphones sound great and stay comfortable over marathon streaming or production sessions. Included XLR Cable To top it all off, PreSonus threw in a 10-foot XLR cable for connecting your mic to your interface.

Universal Audio 710tfd Twin-finity Single-channel Microphone Preamp

Universal Audio 710TFD Twin-Finity Single-Channel Microphone PreampThe award-winning 710 Twin-Finity & trade; is a radical UA mic preamp design that combines both the classic retro warmth of tubes with the transient bite of solid-state, all in a 2U, half-rack unit. The 710 was created specifically to add the tonal versatility and sonic inspiration missing from generic audio interface preamps.Tone blending is continually variable between 100% tube and 100% solid-state, offering a practically infinite range of unique preamp tones, plus the ability to easily dial-in your own signature sound. There are lots of sensibly priced solid-state and tube preamplifiers out there, but the 710 Twin-Finity is the only one that offers the best of both worlds & mdash; as well as everything in-between & mdash; all in one box, and within reach of any serious project studio & rsquo;s budget. Includes a 19 & Prime; rack-kit for mounting one or two units.Harness the distinct sonic properties of tubes and solid-state in one unique preamp/DIBlend between tube and solid-state sounds for myriad textures and tonesUnlock the potential of your mic locker with a powerfully versatile preampEasily track guitar, bass, or keyboards with the front panel 1/4 & ldquo; Hi-Z instrument input

Active Microphone Splitter With 2 Preamps Per Input - Dl231 24×24

Midas DL231 24 & times;24 Active Microphone Splitter with 2 Preamps per Input The DL231 is an Active Microphone Splitter from Midas with 24 inputs and 24 outputs. With two independent Midas microphone preamplifiers per input channel with switchable 48V phantom power. This microphone splitter features a PCB layout specifically designed to maintain grounding as well as separation for both analog and digital signals. It comes fitted with an Ethernet control port and four AES50 ports for dual-redundant handling of two independent digital audio interfaces. MIDI in, out, and thru ports are also on board for use with Midas consoles. 24 Input, 24 Output Active Microphone Splitter with 2 Independent Midas Microphone Preamplifiers per Input 2 award-winning Midas microphone preamplifiers per input with switchable +48 V phantom power 2 dual redundant AES50 network ports with independent phase-locked loop synchronisation 24 electronically balanced output channels can be sourced from microphone preamplifiers or AES50 ports Remote operation up to 100 m via CAT5/5e cable Selectable 96 kHz or 48 kHz sample rate operation All settings programmable from front panel controls or console PSU status indicator LEDs and configuration LCD display on front panel MIDI In, Out and Thru connectors Features Neutrik etherCON* AES50 network ports Rugged 5U rackmount chassis for durability in portable applications Dual redundant auto-ranging universal switch-mode power supplies

U-phoria Studio Pro

U-PHORIA STUDIO Looking for the ideal way to express yourself? Ever dreamed of becoming a famous producer? Then podcasting is the answer and the U-PHORIA STUDIO bundle has everything you need to make high-quality podcasts, produce your own music and home recordings! Included in this incredible recording bundle you & rsquo;ll find a U-PHORIA UM2 USB audio interface, C-1 condenser microphone and HPS5000 studio headphones. Just add your favorite DAW and you & rsquo;ll be up and running in mere moments & ndash; right out-of-the-box U-PHORIA UM2 That & rsquo;s why we & rsquo;re kicking it up a notch with the amazing UM2, an ultra-compact 2x2, 48 kHz USB audio interface with a studio-grade XENYX Mic Preamp, combination XLR/TRS input for your vocal or line input and an additional & frac14;" direct Instrument Input (no DI box required). Studio-Grade C-1 Mic The C-1 microphone is a professional-quality condenser microphone designed to capture your sound with incredible realism, sensitivity and accuracy. With C-1 & rsquo;s outstanding cardioid pickup pattern for excellent sound source separation and feedback rejection, this ultra-low noise mic is an excellent choice for any recording scenario. The C-1 just may be the only microphone your studio will ever need. Professional HPS5000 Headphones HPS5000 headphones provide everything you need for comfortable listening. The ear cups contain high-efficiency cobalt capsules that deliver high-definition bass and super-transparent treble. Featuring a single-sided cord that resists tangling, an ultra-comfortable headband and a 1/4" adapter for the 1/8" connector, HPS5000 phones are compatible with everything from your smartphone & ndash; to your mixing console. Superb Performance, Super-Affordable Get on the air immediately with the fantastic U-PHORIA STUDIO recording package. This amazing bundle includes a U-PHORIA UM2 USB audio interface, a pair of high-quality HPS5000 headphones, a great-sounding C-1 studio-grade condenser microphone & ndash; and all the cables you & rsquo;ll ever need. See your local Behringer dealer, or get your U-PHORIA STUDIO online today & ndash; and become part of the global broadcast revolution!

Klark Teknik Dn32-adat Adat Expansion Module

ADAT* expansion module for Midas and Behringer digital consoles Up to 32 channels of simultaneous recording and playback @ 48 kHz Features 4 input and 4 output TOSLINK* optical fibre connectors BNC word clock input or output for external clock synchronisation Ideal for studio and live recordings with ADAT-equipped HD recorders Optical fibre connections eliminate ground loop interference ADAT Expansion Module With up to 32 bidirectional channels for Midas M32 or Behringer X32 Simultaneous recording and playback of up to 32 channels at 48 kHz Provides 4 inputs and 4 outputs via optical TOSLINK connection BNC Word Clock input or output for external clock synchronisation Ideal for studio and live recordings with ADAT-equipped HD recorders ADAT* expansion module for Midas and Behringer digital consoles Up to 32 channels of simultaneous recording and playback @ 48 kHz Features 4 input and 4 output TOSLINK* optical fibre connectors BNC word clock input or output for external clock synchronisation Ideal for studio and live recordings with ADAT-equipped HD recorders Optical fibre connections eliminate ground loop interference ADAT Expansion Module With up to 32 bidirectional channels for Midas M32 or Behringer X32 Simultaneous recording and playback of up to 32 channels at 48 kHz Provides 4 inputs and 4 outputs via optical TOSLINK connection BNC Word Clock input or output for external clock synchronisation Ideal for studio and live recordings with ADAT-equipped HD recorders

Pf8 Acoustic Filter Microphone

Alctron PF8 uses high quality noise reduction foammachining into cylinder microphone wind screen. PF8 upgrade, the bottom is designed to be curved, suitable for more microphones and shock mounts.Alctron PF8 helps your microphone isolating in a quiet environment, under this environmentmicrophone will record your voice exclusively.The PF8 is able to capture thecomplete spectrum of your voice and reduce much of the external environment,all the while giving you clear and concise vocals free of any coloration.PF8 wind screen not only reduce the reflection of recording sound but also reducethe external wind and noise to disturb recording.Maintaining Cleanness of Mics: Functionally prevents saliva spraying, other harmful dust and moisture.

Presonus Monitor Station V2: The Desktop Speaker-management Solution.

Studio Monitor & Headphone Controller Inputs: 2 x stereo line, 2 x stereo Aux, 1 x coaxial S / PDIF (44.1 / 48 / 88.2 / 96 kHz) Master volume control Cue volume control 2 x three source selection button with two shift modes (individual / alternative) Separate button for selecting from 3 pairs of studio monitors with three control modes 3 Rear trim control for level adjustment of the connected speakers Integrated electret condenser microphone for talkback Mute and Mono button Dim button with adjustable attenuation Calibratable 2 x 8-segment LED level meter 4 Separate headphone controls Source (Main or cue) per headphone output selectable 3 Speaker outputs (stereo) 2 Stereo line outputs (Main and Cue) Dimensions (L x W x H): 229 x 216 x 64 mm Weight: 4.6 kg Including power adapter

Klark Teknik - Expansion Module With Up To 32 Bidirectional Channels - Dn32-usb

USB 2.0 expansion module for Midas and Behringer digital consoles Up to 32 bidirectional channels @ 48 kHz of recording and playback Simultaneous computer audio recording and playback Operates from console USB device clock Enables remote control of compatible DAW software via emulations of Mackie Control* and HUI* protocols Seamless computer integration for virtual sound checks and software plug-ins Ultra-low latency ASIO* drivers available for Windows Class-compliant USB design compatible with Mac OS X CoreAudio* & ndash; no driver required

Desktop Livestreaming Microphone Mobile Phone Stand With Mic Clip

-Desktop Multifunctional Microphone Stand -Fit for live streaming, singing meeting, speech and recording - 180 degree Angle adjustable, height adjustable, stable and solid base -Compatible with different microphones - Stable structure: The table microphone tripod features stable structure. It can be placed on the desktop steadily, not easy to slide. - Good workmanship: The microphone holder is made by good workmanship, smooth and flat in surface, without burrs, good choice for microphone accessory.

Presonus Hp2: Personal Monitoring For Stage And Studio.

PreSonus & reg; HP-series headphone amplifiers have long been popular for their loud, clean, clear sound and roadworthy built quality. Designed for musicians and performers who demand mobility without compromising audio quality, the HP2 personal headphone amplifier is a great choice for driving wired in-ear monitors (IEMs), as well as headphones. The new HP2 delivers these qualities in an easily affordable, stereo device so you & rsquo;ll hear every note and beat clearly wherever your music takes you. Portable and compact, the HP2 gives you all you need to drive your headphones or in-ears without complicating your setup. It sports two XLR line-level inputs and one stereo 1/8-inch headphone output with volume control. Operation can be switched between stereo and mono, and a Pan knob is provided. Like all PreSonus gear, it & rsquo;s built to take the rigors of life on the road. And it mounts on a microphone stand or clips to your belt. Simple, easy to use, built to travel, has the right features, sounds great. Features Meters, Controls, and Features Battery-powered, stereo headphone amplifier Volume control knob Pan control knob Stereo/mono operation switch Battery-health LED indicators Belt clip Input/Output Inputs: 2 female XLR connectors Output: stereo, 1/8 & rdquo; phone connector 2m cable (5-pin mini XLR to 2 female XLRs) included Physical and Power 9V battery or DC power supply 5/8-inch (27 tpi) microphone stand-mount socket Mobile stereo headphone amplifier Ideal for wired in-ear monitoring Also suitable for mobile recording 2 Mounting options: Belt clip or 5/8" thread for tripod mounting Input: 2 x XLR female (Line L/R) via enclosed breakout cable Large volume control Large panorama control Panpot also serves as balance control between input 1 and 2 in mono mode Output: TRS stereo jack (3.5 mm) Frequency range: 30 Hz - 20 kHz ( & plusmn;2 dB) Maximum input level: +4 dBV Output power: 50 mW/channel ( & lt;0.01% THD+N @ 20 Ohm) Minimum impedance of headphones used: 12 Ohm Power supply: 9 V block battery (not included) or mains adapter On/off switch on the back Power LED Battery control LED Dimensions: 134 x 73 x 32 mm Weight: 450 g (without battery) Incl. 2 m breakout cable (mini 5-pin XLR to 2 x XLR female) and power supply unit (9 V/40 mA)

Sound Card – Presonus Audio Box Ione

PreSonus Studio AudioBox iOneAudioBox iOne makes it easy to capture ideas and create professional-quality recordings.The AudioBox iOne audio interface for guitarists and songwriters on the go. Inspiration is everywhere for singers/songwriters, so bring your studio with you and record wherever you go. The two-input PreSonus AudioBox & reg; iOne lets you capture your voice and instrument on your Mac, Windows PC, and iPad. Simply plug in your guitar and microphone, and you & rsquo;re ready to create! USB bus-powered and bundled with powerful, easy-to-use recording software, the AudioBox iOne makes it easy to capture ideas and create professional-quality recordings. Sound Card & ndash; PreSonus AudioBox iOneBuilt to travel.AudioBox iOne is a mobile audio interface in the best sense of the term. It can sit on a tabletop or fit in the pocket of a backpack or laptop bag and works with standard iOS power accessories. Its metal chassis is built like a small tank & mdash;yet it weighs just 1.35 pounds (0.63 kg). Wherever your travels take you, whenever your creative muse calls, your AudioBox iOne audio interface will be ready to help you compose and record your masterpiece. Sweet-sounding Mic Preamp that will Capture Your Voice in all its GloryTo record great-sounding music, you need outstanding preamps and digital converters. And to hear what you & rsquo;re doing, you need a headphone amp that keeps up with the rest of the design. The AudioBox iOne audio interface delivers it all! We & rsquo;re famous for our award-winning microphone preamplifiers, and we & rsquo;ve equipped the AudioBox iOne with a new, sweet-sounding mic preamp that will capture your voice in all its glory. Clean, clear, 24-bit, 96 kHz digital converters and an ultra-loud, crystal-clear headphone output ensure you hear every detail. Mobile recording made easy.The AudioBox iOne audio interface and its software library make recording your compositions and tracks easy! Record in stereo on your iPad with free Capture & trade; Duo or record up to 32 tracks with affordable Capture for iPad. Then wirelessly beam your iPad tracks to our award-winning Studio One & reg; recording and production software for Mac or Windows for editing and mixing. Or do the whole project on your laptop with Studio One. Either way, the AudioBox iOne and its software library provide all the tools needed to record on the road and in the studio.

Presonus Audiobox Go

AudioBox GO: ultra-affordable, compact 2 & times;2 USB audio interface PreSonus AudioBox GO | USB-C Audio Interface for music production with Studio One DAW Recording Software, Music Tutorials, Sound Samples and Virtual Instruments: Musical Instruments Connect anything and sound great. The AudioBox GO & trade; features a PreSonus & reg; XMAX-L preamp, designed with over 25 years of recording-studio know-how. Not only does it ensure that your recordings will sound clean and articulate with low noise, but it also provides 50 dB of gain and +48v phantom power for professional XLR condenser microphones. The combo jack doubles as a line-level input that you can use to record keyboards, drum machines, and more! A dedicated Instrument input lets you connect an electric guitar or bass, so you can record guitar and vocals at the same time. Small is beautiful. True to its name, the AudioBox GO & trade; is so powerful and loaded with features, you & rsquo;ll want to take it with you everywhere & mdash; so we made it small enough to toss into your guitar case or your laptop bag. AudioBox GO works great with Android and Apple mobile devices & mdash; but also with both laptop and desktop computers, making it an ideal interface for small home studios. It & rsquo;s USB class-compliant, so there are no special drivers or applications for you to download and install. And because it & rsquo;s bus-powered, there & rsquo;s no power supply to fuss around with. Loud and clear. The AudioBox GO & trade; lets you connect professional studio monitors like the PreSonus Eris-series to its balanced Main outputs, while also providing a surprisingly powerful Headphone output that lets you listen in loud and clear. You also get an easy-to-use Mix control to create a monitor mix by blending the audio from your hardware inputs and your software so you can record vocals while listening to the tracks you & rsquo;ve already recorded and stay inspired. World-class recording software included. While the AudioBox GO & trade; audio interface works with virtually all macOS & reg; and Windows & reg; audio-recording software, it comes with a free license for Studio One & reg; Prime, giving you a complete recording solution. Built by creative people for creative music production, Studio One is easy to learn and enables you to compose, record, and produce your masterpiece without getting distracted by the tools. And when you & rsquo;re ready to hit the road, download Capture Duo for free and enjoy two-track recording on the go. AudioBox GO Features | PreSonus AudioBox Go Ultra-affordable, ultra-compact, versatile USB-C & reg; compatible audio interface for home and mobile recording with professional sound quality Recording Software included: Get started right away with Studio One & reg; Prime DAW recording software and Studio Magic software bundle including music tutorials, tons of sound samples, and virtual instruments. Bus-Powered: AudioBox GO is powered by your connected USB-C & reg; device so no need for an additional power supply & ndash; works great with both Apple & reg; and Android & trade; devices. Connect an instrument and a microphone at the same time: 1 TS instrument input to record guitar or bass and 1 XLR mic/line combo input to record vocals or a keyboard, drum machine, or other line-level instrument. Headphone Connection: 1 TRS 1/4 & rdquo; stereo headphone output with mix control lets you create a custom blend between your inputs and playback so you can monitor your recording with zero latency. Speaker Connections: 2 balanced TRS 1/4 & rdquo; main outputs for studio monitors or speakers. Professional Audio Quality: Studio-grade converters allow for up to 24-bit/96 kHz recording and playback assuring the highest quality possible. Professional XMAX-L Mic Preamp: Your microphone will sound its best thanks to this custom low-noise, high-headroom design with 50 dB of adjustable gain and switchable +48V phantom power for professional XLR condenser mics PreSonus AudioBox GO | USB-C Audio Interface for music producer | The New PreSonus AudioBox GO | AudioBox GO Features of PreSonus AudioBox Go | Shop & Buy PreSonus AudioBox GO | Price of PreSonus AudioBox | Specifications of AudioBox Go | AudioBox GO: ultra-affordable, compact 2 & times;2 USB audio interface

Steel And Round Base Microphone Stand

This is a solid made microphones stand with metThisallic materials It has a round based support which helps in ballancing It has a boom that helps in heights Made o metal althrough Can be use any where This popular microphone stand is favoured by bands, schools, colleges and teachers. Features a sturdy cast steel, weighted base which offers stability for stage and studio performances. Manufactured with tough, durable and reliable materials that meet REACH standards and live up to high expectations. Adjust the height of the stand to meet your ideal level between 84cm and 153cm. We are so confident in the quality of our stands

Arturia Microfreak Experimental Hybrid Synth

MicroFreak EXPERIMENTAL HYBRID SYNTH A synthesizer like no other, MicroFreak is a peculiar, exceptional instrument that rewards the curious musician. It blends wavetable and digital oscillators with analog filters. It features a unique poly-aftertouch flat keyboard. It adds controlled randomness to sequences. This isn & rsquo;t a revolution, it & rsquo;s a mutiny. Whether you & rsquo;re looking for your first, affordable hardware synth or are a collector looking for original sounds and unique interface, MicroFreak is the synth you need. Small but fierce MicroFreak packs so much in to such a compact instrument, you & rsquo;ll wonder how we did it. We & rsquo;d love to say it was magic, but it was pure skill and passion. The best of both worlds Even though MicroFreak has a digital oscillator at its heart, & ldquo;opposites attract & rdquo; as the saying goes. That & rsquo;s why we & rsquo;ve included a lush-sounding analog filter. Product Description A synthesizer like no other, MicroFreak is a peculiar, exceptional instrument that rewards the curious musician. It blends wavetable and digital oscillators with analog filters. It features a unique poly-aftertouch flat keyboard. It adds controlled randomness to sequences. This isn & rsquo;t a revolution, it & rsquo;s a mutiny. This out-there little music machine features a versatile digital oscillator so you can create rare and interesting sounds with ease. Modes like Texturer, KarplusStrong, Harmonic OSC, and Superwave give adventurous musicians the chance to explore totally new, unheard possibilities. Like having dozens of synths in just one instrument, both wild-eyed newcomers and seasoned professionals will fall in love with MicroFreak & rsquo;s flexible, powerful synth engine. Physical modelling, wavetable synthesis, virtual analog, there is nothing as complete and exciting as the MicroFreak oscillator on the market. It's hard to believe from such a small synth, but here it is, ready for you to explore. Excite your creativity and reward your curiosity with a large, diverse sound palette. MicroFreak features 11 awesome oscillators, 4 bespoke Arturia engines, and 7 modes from our friends at Mutable Instruments. Inspired by the trailblazing 12-dB Oberheim SEM filter, you can make MicroFreak & rsquo;s filter scream or whisper to taste. The filter is state-variable, and can even auto-oscillate! You can use this is any way you like, from taking the edge of the razor-sharp wavetable sounds, or automating the cutoff by modulating it with keyboard pressure or the in-built sequencer. Record up to four automations, edit notes per step or use the innovative Spice and Dice sequencer functions to find happy accidents. Add randomization to create evolving, original patterns, and virtually rewire and reconfigure its signal chain and controls with the 5x7 modulation matrix.

Alctron Ms180 5" Desktop Speaker Stand Pair - Black

MS180 desktop speakers stands from Alctron designed for 5" studio monitors. Constructed with a heavy metal base to ensure stability and includes a padded shelf to isolation from vibrations, reducing the need for isolation pads. Height and angle adjustable MS180-5 Multi-Angle Height Adjustable Desktop Speaker Stand - Pair - 5" / 5 inchThe MS180-5 are a high quality desktop monitior stand designed for 5" studio monitor speakers, constructed with a heavy metal base to ensure stability and includes a padded shelf to isolation from vibrations and reducing the need for isolation pads. The MS180 speaker stands have the capacity to be height and angle adjustable. Made from solid steel and aluminium, these sturdy stands allow you to set the optimal position for your speakers. Ideal for professional or home use, it can be used in studio or home theatre monitoring. Sturdy and Built to LastThe speaker stands are made from solid steel, aluminium and rubber. The rubber cap in the top plate and four rubber pads reduce the vibration during the listening experience, effectively isolating the monitors from the desk surface. The top tray is non-slip for stable mounting. The pads under the base act as an anti-slip and anti-shock system. The solid steel and aluminium core components are built to last. Each stand can hold up to 15kg. Features: Tilt speaker stand. Solid Steel and aluminium with rubber components. Ultra design. Anti-slip tray. Ball adjustment system. Vibration absorbing rubber feet.

24 Channels Audio Link Snake Cable With Rim

24 channel multicore cable on a portable extendable reel style stage box, featuring Ningbo Neutrik connectors. Features 20 XLR balanced send and 4 return channels. Instruments (DI Box) and microphones are plugged into the send inputs marked 1 to 20 on the stagebox. The signals are carried through the multicore to 20 corresponding XLR(m) number coded connectors. There are 4x XLR(m) return outputs on the stage box marked A to D. These channels connect to 4x XLR(f) connectors which are used to take the output signals of the mixer back to the stage box for connections with amplifiers and speakers. Typically used to connect performers on stage to a mixing desk. This is a excellent quality fully shielded, balanced multicore cable on a reel featuring Ningbo Neutrik XLR connectors on both the stage box and fan end. Comes with 4 attachable wheels for easy maneuvering, two of which can lock to ensure the Reel stays safely in one place during the show. Reel stage box for easy usage 20 balanced Send Channels 4 balanced Return Channels 30 meter cable length Neutrik Connectors - Stage box (YS145, YS146) - Fan (YS136N, YS137N)

Vocal Booth Mic Reflection Filter

Ambient and reflected sound can be a problem when recording acoustic and vocal tracks, especially in a "live" studio environment. Block unwanted sounds from entering your microphone by using this Microphone Isolation Shield from Monoprice! This acoustic shield features an acoustic foam front and a vented metal back plate, which allows the microphone to "breathe" and prevents reflections within the arc of the shield. It uses a dual clamp mounting bracket, which attaches to booms or stands up to 1 1/4" in diameter. The two outer panels can be folded inward for storage or for creating a tighter acoustic isolation chamber. The shield features a standard 3/8" microphone threaded mount and includes a 3/8" to 5/8" thread adapter. The shield can be used in a normal upright orientation or can be inverted, so that the microphone hangs down inside the chamber. All assembly and mounting hardware is included. Ambient and reflected sound can be a problem when recording acoustic and vocal tracks, especially in a "live" studio environment. Block unwanted sounds from entering your microphone by using this Microphone Isolation Shield from Monoprice! This acoustic shield features an acoustic foam front and a vented metal back plate, which allows the microphone to "breathe" and prevents reflections within the arc of the shield. It uses a dual clamp mounting bracket, which attaches to booms or stands up to 1 1/4" in diameter. The two outer panels can be folded inward for storage or for creating a tighter acoustic isolation chamber. The shield features a standard 3/8" microphone threaded mount and includes a 3/8" to 5/8" thread adapter. The shield can be used in a normal upright orientation or can be inverted, so that the microphone hangs down inside the chamber. All assembly and mounting hardware is included.

Audient Id14 10 in - 6 Out Audio Interface - mkii

Audient iD14 (MKII) 10in | 6out Audio Interface. Designed to take your recordings to the next level in every way, the iD14 (MKII) delivers professional audio performance in a compact and modern desktop package, giving you everything you need to make studio quality recordings at home. Every iD interface features the Audient Console Mic Preamp, the same discrete circuit design found in our renowned recording console the ASP8024-HE. Designed to deliver ultra- low noise and low distortion with a touch of classic analogue warmth, iD14 & rsquo;s two Audient mic pre & rsquo;s will give you the professional sound you deserve. The Audient mic pre is a high grade hybrid discrete and op amp design that delivers a clean, accurate and detailed translation of your source. With a noise floor 30,000 times quieter than the signal level your recordings will be captured with stunning clarity. iD14 & rsquo;s converters make sure you hear every nuance, every detail of your audio, enabling you to take your recordings to the next level. Offering an incredible 126dB of dynamic range you will hear your audio more accurately, make better creative decisions and experience stunning clarity directly from your desktop. Plan for the future with iD14 & rsquo;s digital input. Supporting both ADAT and SPDIF, iD14 gives you the option to add up to eight extra mic pre inputs letting you expand your rig and take on larger sessions. D.I / Instrument Input RANGE: 40dB LINEUP: 12dBu = 0dBFS THD+N @ 0dBu: 0.1% SNR: 100dBu A-Weighted FREQUENCY RESPONSE & ndash; MIN GAIN & plusmn;0.5dB 10Hz to 20kHz 1/4 & rdquo; TS JACK: Tip (Hot) & Sleeve (Shield) Microphone preamplifier GAIN RANGE: 58dB LINEUP: 12dBu = 0dBFS MIC MAX INPUT LEVEL: 12dBu MAX INPUT LEVEL: 21dBu INPUT IMPEDANCE (Mic): 2.8k INPUT IMPEDANCE (Line): & gt;8k THD+N @ 0dBu 0.00170% SNR: 101dBu A-Weighted EIN: 129dB A-Weighted CMRR @ 1k: & gt;75dB CROSSTALK: & gt;-100dB FREQUENCY RESPONSE & ndash; MIN GAIN & plusmn;0.5dB 10Hz to 40kHz XLR COMBI FEMALE: Pin 2 (Hot), Pin 3 (Cold) & Pin 1 (Shield) 1/4 & rdquo; TRS JACK: Tip (Hot), Ring (Cold) & Sleeve (Shield) Analogue to Digital Converter THD+N @ -1dBFS: 0.001% DYNAMIC RANGE: 120dB A-Weighted CMRR: & gt;80dB FREQUENCY RESPONSE: & plusmn;0.5dB 10Hz to 40kHz Line Outputs (DAC): LINEUP: 12dBu = 0dBFS THD+N @ -1dBFS: 0.0006% DYNAMIC RANGE: 125.5dB A-Weighted CROSSTALK: & gt;120dB FREQUENCY RESPONSE: & plusmn;0.1dB 10Hz to 40kHz 1/4 & rdquo; TRS JACK: Tip (Hot), Ring (Cold) & Sleeve (Shield) Headphone Outputs: LINEUP: 18.5dBu = 0dBFS THD+N @ -1dBFS: 0.0009% DYNAMIC RANGE: 125.5dB A-Weighted CROSSTALK: & gt;116dB FREQUENCY RESPONSE: & plusmn;0.25dB 10Hz to 40kHz MAXIMUM LEVEL @ 30R: 2.59V Peak, 1.827V RMS, 223mW MAXIMUM LEVEL @ 62R: 4.18V Peak, 2.95V RMS, 280mW MAXIMUM LEVEL @ 600R: 7.72V Peak, 5.46V RMS, 100mW 1/4 & rdquo; TRS JACK: Tip (Left), Ring (Right) & Sleeve (Shield) USB-C High Speed: BUS POWER: MIN REQUIREMENT: 0.9A @ 5V & gt;=USB 3.0 Port MAX REQUIREMENT: 1.5A @ 5V USB-C: Provides higher headphone outputs levels No. of INPUT CHANNELS: 10 No. of OUTPUT CHANNELS: 16 DSP MIXER LATENCY ROUND TRIP (in-to-out): 44.1kHz 0.65mS 48.0kHz 0.6mS 88.2kHz 0.33mS 96.0kHz 0.31mS

M-track 2x2 Vocal Studio Pro

The M-Audio M-Track 2X2 Vocal Studio Pro puts nearly everything you need to record vocals at your fingertips, including an audio interface, a pair of headphones, a condenser microphone, and an included software bundle. All you need to provide is the corresponding computer, an XLR cable, and some vocal cords. The included M-Track interface gives you two inputs and two outputs. It connects over USB to your computer, from which it also draws its power. Through the M-Track's low-noise preamps and A/D converters, you can capture studio-quality recordings. You'll note an XLR/TRS microphone/line combo input, as well as a 1/4" instrument input specifically designed for guitars or basses plugged directly into the interface. The M-Audio M-Track 2X2 Vocal Studio Pro puts nearly everything you need to record vocals at your fingertips, including an audio interface, a pair of headphones, a condenser microphone, and an included software bundle. All you need to provide is the corresponding computer, an XLR cable, and some vocal cords. The included M-Track interface gives you two inputs and two outputs. It connects over USB to your computer, from which it also draws its power. Through the M-Track's low-noise preamps and A/D converters, you can capture studio-quality recordings. You'll note an XLR/TRS microphone/line combo input, as well as a 1/4" instrument input specifically designed for guitars or basses plugged directly into the interface. The M-Track connects to a Mac or Windows computer via a standard USB or USB Type-C port using one of the two included cables. The Hi-Speed USB connection combined with the USB/Direct balance knob delivers zero-latency monitoring of the inputs, and an included software bundle provides everything needed for the solo artist to start recording. Also included with this package is the Nova Black microphone, a cardioid condenser mic with a wide and smooth frequency response. A pair of HDH40 headphones can be used to monitor vocals as your recording, or can be used to listen back to what you've recorded as you mix with the included software bundle. The M-Track connects to a Mac or Windows computer via a standard USB or USB Type-C port using one of the two included cables. The Hi-Speed USB connection combined with the USB/Direct balance knob delivers zero-latency monitoring of the inputs, and an included software bundle provides everything needed for the solo artist to start recording. Also included with this package is the Nova Black microphone, a cardioid condenser mic with a wide and smooth frequency response. A pair of HDH40 headphones can be used to monitor vocals as your recording, or can be used to listen back to what you've recorded as you mix with the included software bundle.

Design Atem Television Studio Pro 4k Live Production Switcher

Brand Warranty Period 6 Months Blackmagic Design ATEM Highlights8-Channel 12G-SDI SwitcherHD and UHD Signal-Compatible to 2160p6012-Input, 2-Channel Audio MixerRe-Sync on All InputsUHD 4K Multiview OutputLow-Latency ConverterBuilt-In Talkback FeatureCCU Control for Select CamerasATEM Advanced Chroma KeyerPowerful DVE Processor, 2 x Clip PoolFeaturesThe Blackmagic Design ATEM Television Studio Pro 4K is a UHD 4K-compatible, 8-input live production switcher with an integrated control panel, suitable for broadcast, sports, web, and A/V productions. This versatile switcher's eight independent 12G-SDI inputs accept all popular HD and UHD signals up to 2160p60. A re-syncing feature on each input enables you to seamlessly use an amalgam of pro and consumer cameras, game consoles, and computer feeds. Switch, add effects, color grade, and key in real time using the control surface's buttons, knobs, and slider. CCU functions are available for controlling Blackmagic Studio and URSA Mini/Broadcast/Micro Studio cameras from the switcher. A software-based control panel is included and may be used independently, or on multiple laptops for delegating multicamera control. The ATEM Advanced Chroma Keyer, with one upstream and two downstream keys, offers live graphics and virtual set creation with improved image control and spill correction. Create PiP effects, resize and scale live video, and choose from 17 powered transitions with the ATEM Television Studio Pro 4K'S DVE processor. Multiview output is available for all eight channels, via HDMI or SDI, complete with tally, labeling, audio metering, and safe-area marking. A talkback function is available for director/operator communication with compatible cameras. The integrated Fairlight audio mixer features six-band parametric EQ, compression, limiting, and stereo simulation on analog and mic inputs. Mix solely from the panel, or use the multitrack interface on your Mac or Windows PC. Use the auxiliary output port to send your switched program or clean feed to a large-scale screen or other display. FeaturesEight 12G-SDI inputs, each with re-sync and low-latency conversionSupports HD video signals up to UHD 4K 2160p6012-input, 2-channel Fairlight audio mixerUHD 4K multiviewer with up to 10 windowsCCU functions for compatible camerasATEM advanced chroma keyerIntegrated talkback feature for compatible camerasPowerful DVE processor, 2-clip media pool with fill and keyMac and PC compatible

Audient Id14 (mkii) 10in 6out Audio Interface

Audient iD14 (MKII) 10in | 6out Audio Interface The Audient mic pre is a high grade hybrid discrete and op amp design that delivers a clean, accurate and detailed translation of your source. With a noise floor 30,000 times quieter than the signal level your recordings will be captured with stunning clarity. iD14 & rsquo;s converters make sure you hear every nuance, every detail of your audio, enabling you to take your recordings to the next level. Offering an incredible 126dB of dynamic range you will hear your audio more accurately, make better creative decisions and experience stunning clarity directly from your desktop. Plan for the future with iD14 & rsquo;s digital input. Supporting both ADAT and SPDIF, iD14 gives you the option to add up to eight extra mic pre inputs letting you expand your rig and take on larger sessions. 2 x Audient Console Mic Preamps Dedicated talkback technology which helps you to use any audio source connected to your computer such as a built in or USB microphone as your talkback mic, freeing up valuable mic pres for recording Advanced monitoring features to the iD button, including DIM, CUT, Polarity Reverse, Mono Sum, Talkback or Cue Mix monitoring. Adding value to your purchase, Austin Bazaar bundles your instrument with necessary accessories. Everything you need to start playing immediately comes in one box. Save yourself the hassle and save some money while you're at it. An instrument cable is included so you have an extra. An XLR cable is included so you can plug in right away. An Austin Bazaar polishing cloth is included so you can keep your new instrument in mint condition.Designed to take your recordings to the next level in every way, the iD14 (MKII) delivers professional audio performance in a compact and modern desktop package, giving you everything you need to make studio quality recordings at home.Audient Console Mic PreampsThe id14 features two Audient Console Mic Preamp, that deliver ultra-low noise and low distortion with a touch of classic analogue warmth, giving you the professional sound you deserve.Class leading convertersOffering an incredible 120dB of dynamic range you will hear your audio more accurately, make better creative decisions and experience stunning clarity directly from your desktop.Speaker OutputsConnect and listen to your mixes through two sets of speakers with iD14 & rsquo;s four line outputs. Also use the extra line outputs to send audio to an external headphone amp for distribution to your artists.JFET Instrument InputDesigned to replicate the input stage of a classic valve amplifier, iD14 & rsquo;s harmonically rich JFET Instrument Input is the perfect sonic foundation for your guitar or bass and amp sims.Expand via ADATPlan for the future with iD14 & rsquo;s digital input. Supporting both ADAT and SPDIF, iD14 gives you the option to add up to eight extra mic pre inputs letting you expand your rig and take on larger sessions.Audio Loop-backAudio Loop-back enables you to capture playback from applications on your computer at the same time as your microphones.ScrollControlTurn iD14 & rsquo;s vo

Scarlett 2i2 Soundcard - 3rd Gen - USB

Brand The most popular audio interface for artists across all genres, the third-generation Scarlett 2i2 provides two mic/line/instrument inputs allowing simultaneous recording and playback of up to two channels with independently controllable headphone and monitor outputs. The 2i2 features two upgraded third-generation Scarlett mic preamps: with optional Air setting to reproduce the Air effect of Focus rite's ISA mic preamp, giving your vocal and acoustic recordings a brighter and more open sound. Equipped with high performance 24-bit/192kHz AD-DA converters, Scarlett s the same professional sound quality throughout the third-generation range. The high impedance, high-headroom instrument inputs allow you to record guitar or bass without any clipping or unwanted distortion, while Gain Halo metering makes it easy for you to set the input level. Scarlett 2i2 is designed to stand up to days on the road, and connects straight to your Mac or PC via USB cable, with no external power required. It comes with all the software tools you need to get started, including two comprehensive digital audio workstations: Ableton Live Lite and Pro Tools First Focus rite Creative Pack. Intuitive enough for beginners yet advanced enough to inspire real creativity with great-sounding effects. Focus rite has partnered with Splice to give 3rd Gen. interface owners a free 3-month Splice Sounds subscription when setting up a new Splice account. Splice Sounds offers millions of high-quality, royalty-free one-shots, loops, and presets, with new releases daily from your favorite producers, sound designers, and artists. Creators use Splice to make all kinds of music, including chart-topping pop, Grammy-winning albums, underground mixtapes, and cinematic scores. Brand The Scarlett 2i2 hardware interface provides the means for connecting microphones, musical instruments or line level audio signals to a computer running Mac OS or Windows. The signals at the physical inputs can be routed to your audio recording software / digital audio workstation (referred to throughout this user guide as the & ldquo;DAW & rdquo;) at up to 24-bit, 192 kHz resolution; similarly, the DAW & rsquo;s monitor or recorded output will appear at the unit & rsquo;s physical outputs. The physical outputs can be connected to an amplifier and speakers, powered monitors, headphones, analogue mixer or any other analogue audio equipment that you wish to use. Although all inputs and outputs on the Scarlett 2i2 are routed directly to and from your DAW for recording and playback, you can configure the routing within your DAW in order to meet your need. Brand The most popular audio interface for artists across all genres, the third-generation Scarlett 2i2 provides two mic/line/instrument inputs allowing simultaneous recording and playback of up to two channels with independently controllable headphone and monitor outputs. The 2i2 features two upgraded third-generation Scarlett mic preamps: with optional Air setting to reproduce the Air effect of Focus rite's ISA mic preamp, giving your vocal and acoustic recordings a brighter and more open sound. Equipped with high performance 24-bit/192kHz AD-DA converters, Scarlett s the same professional sound quality throughout the third-generation range. The high impedance, high-headroom instrument inputs allow you to record guitar or bass without any clipping or unwanted distortion, while Gain Halo metering makes it easy for you to set the input level. Scarlett 2i2 is designed to stand up to days on the road, and connects straight to your Mac or PC via USB cable, with no external power required. It comes with all the software tools you need to get started, including two comprehensive digital audio workstations: Ableton Live Lite and Pro Tools First Focus rite Creative Pack. Intuitive enough for beginners yet advanced enough to inspire real creativity with great-sounding effects. Focus rite has partnered with Splice to give 3rd Gen. interface owners a free 3-month Splice Sounds subscription when setting up a new Splice account. Splice Sounds offers millions of high-quality, royalty-free one-shots, loops, and presets, with new releases daily from your favorite producers, sound designers, and artists. Creators use Splice to make all kinds of music, including chart-topping pop, Grammy-winning albums, underground mixtapes, and cinematic scores. Brand Focusrite The Scarlett Solo hardware interface provides the means for connecting a microphone and an instrument or line-level audio signals to a computer running Mac OS or Windows. The signals at the physical inputs can be routed to your audio recording software / digital audio workstation (referred to throughout this user guide as the & ldquo;DAW & rdquo;) at up to 24-bit, 192 kHz resolution; similarly, the DAW & rsquo;s monitor or recorded output will appear at the unit & rsquo;s physical outputs. This lets you record & ldquo;real-world & rdquo; instruments into Ableton Live Lite, GarageBand & reg; (or whichever other DAW you may use) along with & ndash; or instead of & ndash; any & ldquo;native & rdquo; sounds already available within your computer. The physical outputs can be connected to an amplifier and speakers, powered monitors, headphones, or any other audio equipment with analog inputs that you wish to use. Although all inputs and outputs on the Scarlett Solo are routed directly to and from your DAW for recording and playback, you can configure the routing within your DAW in order to meet your needs. A Direct Monitoring feature lets you hear what you are playing without the effects of computer latency.

Id4 (mkii) 2 out Audio Interface -2 In 1

Audient iD4 (MKII) 2in | 2out Audio Interface D.I / Instrument Input RANGE: 40dB LINEUP: 12dBu = 0dBFS THD+N @ 0dBu: 0.1% SNR: 100dBu A-Weighted FREQUENCY RESPONSE & ndash; MIN GAIN & plusmn;0.5dB 10Hz to 20kHz Microphone preamplifier GAIN RANGE: 58dB LINEUP: 12dBu = 0dBFS MIC MAX INPUT LEVEL: 12dBu MAX INPUT LEVEL: 21dBu INPUT IMPEDANCE (Mic): 2.8k INPUT IMPEDANCE (Line): & gt;8k THD+N @ 0dBu 0.00170% THD+N @ 0dBu MAX GAIN: & lt;0.04% SNR: 101dBu A-Weighted EIN: 129dB A-Weighted CMRR @ 1k: & gt;75dB FREQUENCY RESPONSE & ndash; MIN GAIN & plusmn;0.5dB 10Hz to 40kHz Analogue to Digital Converter THD+N @ -1dBFS: 0.001% DYNAMIC RANGE: 120dB A-Weighted FREQUENCY RESPONSE: & plusmn;0.5dB 10Hz to 40kHz Line Outputs (DAC): LINEUP: 12dBu = 0dBFS THD+N @ -1dBFS: 0.0006% DYNAMIC RANGE: 125.5dB A-Weighted CROSSTALK: & gt;120dB FREQUENCY RESPONSE: & plusmn;0.1dB 10Hz to 40kHz 1/4 & rdquo; TRS JACK: Tip (Hot), Ring (Cold) & Sleeve (Shield) Headphone Outputs: LINEUP: 18dBu = 0dBFS THD+N @ -1dBFS: 0.0009% DYNAMIC RANGE: 125.5dB A-Weighted CROSSTALK: & gt;116dB FREQUENCY RESPONSE: & plusmn;0.1dB 10Hz to 40kHz MAXIMUM LEVEL @ 30R: 2.59V Peak, 1.827V RMS, 223mW MAXIMUM LEVEL @ 62R: 4.18V Peak, 2.95V RMS, 280mW MAXIMUM LEVEL @ 600R: 7.72V Peak, 5.46V RMS, 100mW 1/4 & rdquo; TRS JACK: Tip (Left), Ring (Right) & Sleeve (Shield) USB-C High Speed: BUS POWER: MIN REQUIREMENT: 0.9A @ 5V & gt;=USB 3.0 Port MAX REQUIREMENT: 1.5A @ 5V USB-C: Provides higher headphone outputs levels No. of INPUT CHANNELS: 2 (2 Analogue) No. of OUTPUT CHANNELS: 2 (2 Analogue) DSP MIXER LATENCY ROUND TRIP (in-to-out): 44.1kHz 0.65mS 48.0kHz 0.6mS 88.2kHz 0.33mS 96.0kHz 0.31mS

M-audio M-track 2x2 Vocal Studio Pro 002

The M-Audio M-Track 2X2 Vocal Studio Pro puts nearly everything you need to record vocals at your fingertips, including an audio interface, a pair of headphones, a condenser microphone, and an included software bundle. All you need to provide is the corresponding computer, an XLR cable, and some vocal cords. The included M-Track interface gives you two inputs and two outputs. It connects over USB to your computer, from which it also draws its power. Through the M-Track's low-noise preamps and A/D converters, you can capture studio-quality recordings. You'll note an XLR/TRS microphone/line combo input, as well as a 1/4" instrument input specifically designed for guitars or basses plugged directly into the interface. The M-Audio M-Track 2X2 Vocal Studio Pro puts nearly everything you need to record vocals at your fingertips, including an audio interface, a pair of headphones, a condenser microphone, and an included software bundle. All you need to provide is the corresponding computer, an XLR cable, and some vocal cords. The included M-Track interface gives you two inputs and two outputs. It connects over USB to your computer, from which it also draws its power. Through the M-Track's low-noise preamps and A/D converters, you can capture studio-quality recordings. You'll note an XLR/TRS microphone/line combo input, as well as a 1/4" instrument input specifically designed for guitars or basses plugged directly into the interface. The M-Track connects to a Mac or Windows computer via a standard USB or USB Type-C port using one of the two included cables. The Hi-Speed USB connection combined with the USB/Direct balance knob delivers zero-latency monitoring of the inputs, and an included software bundle provides everything needed for the solo artist to start recording. Also included with this package is the Nova Black microphone, a cardioid condenser mic with a wide and smooth frequency response. A pair of HDH40 headphones can be used to monitor vocals as your recording, or can be used to listen back to what you've recorded as you mix with the included software bundle. The M-Track connects to a Mac or Windows computer via a standard USB or USB Type-C port using one of the two included cables. The Hi-Speed USB connection combined with the USB/Direct balance knob delivers zero-latency monitoring of the inputs, and an included software bundle provides everything needed for the solo artist to start recording. Also included with this package is the Nova Black microphone, a cardioid condenser mic with a wide and smooth frequency response. A pair of HDH40 headphones can be used to monitor vocals as your recording, or can be used to listen back to what you've recorded as you mix with the included software bundle.

Pop Filters C2 Isolation Shields

C2 Recording Noise Reduction Wind Screen C2 is a moose reduction cylinder desisigned and processed with high quality noise reduction sponge. Circumference through noise sponge. The surrounding noise absorbs and reflects. C2 isolate your microphone in quiet recording space , allowing the microphone to specifically record your voice during recording and singing. C2 can help you record a complete sound spectrum during the recording process and greatly reduce external environmental noise , while also making your recording sound clear and pure. Optimise your voice , capture your pure human voice and reduce and reduce the interference of external noise o the recorded sound. Reduce post-sound trimming. Reduce redundant equalisation and post-production needs. Intergrated blowout gaurd . A detachable blow out gaurd designed on the front to prevent popping sound and erosion of the microphone capsule by saliva during the recording process. Reduce environmental noise and sound reflection. Isolate your microphone in a quiet recording environment while reducing sound reflections.

Vocal Booth Mic Reflection Filter 002

Ambient and reflected sound can be a problem when recording acoustic and vocal tracks, especially in a "live" studio environment. Block unwanted sounds from entering your microphone by using this Microphone Isolation Shield from Monoprice! This acoustic shield features an acoustic foam front and a vented metal back plate, which allows the microphone to "breathe" and prevents reflections within the arc of the shield. It uses a dual clamp mounting bracket, which attaches to booms or stands up to 1 1/4" in diameter. The two outer panels can be folded inward for storage or for creating a tighter acoustic isolation chamber. The shield features a standard 3/8" microphone threaded mount and includes a 3/8" to 5/8" thread adapter. The shield can be used in a normal upright orientation or can be inverted, so that the microphone hangs down inside the chamber. All assembly and mounting hardware is included. Ambient and reflected sound can be a problem when recording acoustic and vocal tracks, especially in a "live" studio environment. Block unwanted sounds from entering your microphone by using this Microphone Isolation Shield from Monoprice!

Alctron U16k Mk3 USB Audio Recording Interface Microphone External USB Sound Card Amplifier

ALCTRON U16K MK3 is an USB audio interface which used for online singing, mobile phone singing, personal recording, online chatting, listening music and so on. This audio interface mic amp combines sound card and effector into one device. 24Bit/96KHz performance chip (when recording, 24bit/96KHz, when playing, 16bit/48KHz.) without any drivers, just plug and play. It has built-in a 48V phantom power and 16 different working modes. Through audio interface panel & rsquo;s various knobs, you can provide different working mode and recording effect.Frequency response: 22Hz to 50kHz (+/-0.2db) Dynamic Range: 90dB, A-weighted Signal-to-Noise Range: -90dB, A-weighted The Alctron U16K MK3 is a fully featured USB Audio interface. It has 2 solid state preamps, zero-latency monitoring, 16 kinds of DSP effects, dual XLR-combo inputs and 48v phantom power for your condenser microphones. Record Vocals and Guitar:The Hi-Z guitar input is routed to channel 1, leaving the combo jack input for channel 2 free to connect a microphone or line level device. Allowing the user to record each channel to separate tracks in the DAW / audio recording software. Add effects to your vocals, and choose whether to have the FX signal recorded or just used for playback through the headphones. Ideal for getting comfortable while recording, but being able to apply effects in post production. A/D Resolution: This audio device has a 24Bit/96KHz processing chip (recording 24bit/96KHz, playback 16bit/48KHz). There are no drivers required, it is simple plug and play. Inputs and Outputs:Apart from the dual XLR-combo inputs, there are two headphone inputs as well, with seperate volume controls. Individual RCA inputs come with their own controller too. Dual headphone outputs are great to share the mix between performer and producer and giving individual volume controls. Power Supply: This unit derives its power from the USB connection. If, however, you might need to use the interface to provide 48v (phantom power) to a connected condenser microphone, or if you would like to use this audio device away from a computer, simply use the included 5V power supply, and you can utilise this audio interface away from a USB connection.

Scarlett Solo Studio 3rd Gen Soundcard

Brand The best performing mic preamps the Scarlett range has ever seen, now with switchable Air mode to give your recordings a brighter and more open sound & bull; Large diaphragm condenser mic enables you to capture studio-quality recordings that are faithful to the original source & bull; The upgraded HP60 MkIII closed-back headphones offer high sound quality and long-lasting comfort, invaluable for recording or mixing & bull; High headroom instrument input allows you to record guitars and basses without any unwanted clipping or distortion & bull; With our Quick Start tool, it's now easier than ever to get up and running Specifications: & bull; Connectivity: USB Type-C & bull; Protocol: USB 2.0 & bull; Form Factor: Desktop & bull; Simultaneous I/O: 2 x 2 & bull; A/D Resolution: 24-bit/192 kHz & bull; Number of Preamps: 1 & bull; Phantom Power: YES & bull; Instrument Inputs: 1 & bull; Line Inputs: 1 & bull; Analogue Outputs: 2 TRS (Balanced) & bull; Headphone Outputs: 1 & bull; Bus Powered: YES & bull; CM25 MkIII Microphone: Cardioid/Condenser & bull; HP60 MkIII Headphones: Closed Back.

Audient EVO Recording Bundle

Audient EVO Recording Bundle Building on Audient & rsquo;s 20+ years of audio design experience, get unrivalled audio quality on your desktop with the clean, warm and accurate EVO preamps & ndash; offering 58dB of gain range. Smartgain Make sure you capture everything perfectly with Smartgain mode. Start playing, singing or talking and Smartgain will automatically set the level of your microphones. Perfect for beginners. Audio Loop-back Audio Loop-back enables you to record your computer audio at the same time as your microphones. Ideal for content creators, podcasters and streamers. A mic for moments Capture every detail and nuance of your performance from the moment you hit record with the SR1 condenser microphone. Its large diaphragm design and versatile nature will give you studio quality recordings no matter the source. SR2000 Its all in the details The SR2000 & rsquo;s Monitoring Headphones not only deliver superior audio performance but have been engineered to provide long lasting comfort. The 40mm Neodymium drivers consistently deliver accuracy and clarity where you need it most, helping to make sure you make the right sonic decisions when recording and mixing. Create instantly Bundled with a free suite of creative software including Cubase LE and Cubasis LE for iOS, you can start recording as soon as you open the box. Key Features Musicians, Podcasters, Producers EVO 4 USB Audio Interface and Headphones Condenser Mic, Shockmount & XLR Cable 2 XLR-1/4" Mic/Line In, 1/4" Hi-Z Input 1 Headphone Output, 2 Monitor Outs Bus Powered, Mac, Windows, iOS Smartgain Automatic Gain Control Loopback for Recording Skype and VoIP DAW, Instruments, Samples, Cabinet Sim A complete home recording package that makes capturing high-quality audio effortless for podcasters, musicians, producers, and content creators, the Audient EVO Start Recording Bundle includes the EVO 4 desktop 2x2 USB Type-C audio interface, the EVO SR1 supercardioid condenser microphone, the EVO SR2000 monitoring headphones, a

Isolation Shield With Pop Filter & Stand - Black

Are you looking for a top quality, yet affordable soundproofing solution for your vocal recordings? Then look no further than this studio microphone isolation shield enclosure! Boasting a strong, metal shell with 5 acoustic foam panels that will block off outside noise, such as air conditioning or computer fans, reduce sound reflections or echo and attenuate unwanted acoustic interference, this soundproof filter will let you record like a pro! The Microphone Isolation Shield from Knox Gear is a professional quality noise canceling shield that was designed to absorb unwanted noises and reduce the amount of room ambiance that is picked up by your microphone during recording. It & rsquo;s lightweight yet heavy-duty, and the folding design makes it easy to transport and store. It & rsquo;s exactly what you need to record vocals, dialogue and other acoustic audio. It easily mounts directly to microphone stands and can be fixed over tabletops. Product Features Reduce room noise, decrease room reflections, and negate flutter echo, with the microphone isolation shield. With its 3 panel, 2 fold design, and high density foam and steel, the isolation shield is ideal for mounting on microphone floor stand or table stand (not included). It connects to a shock mount or microphone. Crisp Vocal Recordings Improve your sound quality with the help of our specially designed microphone shield. With professional studio equipment, you can record the clearest sound. Set up your recording booth. It & rsquo;s perfect for recording vocals, acoustic recording, instruments and dialogue. Use it for studio recording, podcast, YouTube and all other audio. Acoustic foam and soundproof panels effectively eliminate unwanted noises, sounds and rustling.

Audient Id44 (mkii) 20in 24out Audio Interface

Audient iD44 (MKII) 20in | 24out Audio Interface Integrate your favourite outboard FX prior to conversion and start creating signal chains that rival the very best. The insert returns also gives you direct access to the A/D converters providing the cleanest signal path possible, making it great for print-backs or integrating outboard line level sources. Designed to replicate the input stage of a classic valve amplifier, iD44 features two harmonically rich JFET Instrument Inputs giving you the perfect sonic foundation for your guitars or basses before you hit your amp sims. Connect and listen to your mixes through two sets of speakers with iD44 & rsquo;s four line outputs. Alternatively use the extra line outputs to send audio to an external headphone amp for distribution to your artists. Easily record and collaborate with others by utilising iD44 & rsquo;s two individual stereo headphone amps, both providing more than enough power for your headphones to perform accurately. Now equipped with Audio Loop-back, iD44 can quickly transform into a multi-purpose powerhouse. Giving you the ability to capture playback from multiple applications on your computer at the same time as your microphones, Audio Loop-back lets you create a custom audio feed ready to send to your streaming software. Ideal for content creators, podcasters and streamers. iD44 & rsquo;s dedicated talkback technology enables you to use any audio source connected to your computer such as a built-in or USB microphone as your talkback mic, freeing up valuable mic preamps for recording. Specifications Microphone preamplifier MIC GAIN: 0 to +60 dB LINE GAIN: -10 to +50 dB PHANTOM POWER: 48v +/-4v @ 10mA/Channel (12VDC only) MIC EIN: -126dBu CMRR: & gt;80dB @ 1kHz MAXIMUM INPUT LEVEL: +18 dBu INPUT IMPEDANCE (Mic): 3k & Omega; balanced INPUT IMPEDANCE (Line): 10k & Omega; balanced FREQUENCY RESPONSE: & plusmn;0.5 dB 10Hz to 65kHz CROSSTALK: & lt;-90 dBu @ 1kHz & 10kHz THD+N @ 0dBu (1kHz): 0.003% (-96dBu) SNR: 96dB XLR: Pin 2 (Hot), Pin 3 (Cold) & Pin 1 (Shield) 1/4 & rdquo; TRS JACK: TIP (Hot), RING (Cold) & SLEEVE (Shield) D.I / Instrument Input (Channel 1): D.I GAIN: 0 to +60 dB MAXIMUM INPUT LEVEL: +10dBu INPUT IMPEDANCE: 1Meg & Omega; Unbalanced FREQUENCY RESPONSE: & plusmn;0.5 dB 10Hz to 50kHz THD+N @ 0dBu (1kHz): & lt;0.3% SNR: 95dB A-weighted 1/4 & rdquo; JACK: Tip (Hot) & Sleeve (Shield) Analogue to Digital Converter (ADC 1 & 2): (Measured via Insert Returns under AES-17) MAXIMUM INPUT LEVEL: +18 dBu (0 dBFS digital maximum) DIGITAL REFERENCE LEVEL: +18 dBu = 0 dBFS INPUT IMPEDANCE: & gt;10k & Omega; Balanced CROSSTALK: -115 dBu @ 1kHz & 10kHz FREQUENCY RESPONSE: & plusmn;0.5 dB 10Hz to Fs/2 (Nyquist) CROSSTALK: -115dBu @ 1kHz & 10kHz THD+N @ -1dBFS (1kHz): & lt;0.0003% (-112dB) DYNAMIC RANGE: 120 dB A-weighted 1/4 & rdquo; TRS JACK: TIP (Hot), RING (Cold) & SLEEVE (Shield) Digital to Analogue Converter (DAC 1 & 2): (Measured under AES-17 at line outputs 1 & 2) MAXIMUM INPUT LEVEL: +18 dBu (0 dBFS digital maximum) DIGITAL REFERENCE LEVEL: +18 dBu = 0 dBFS OUTPUT IMPEDANCE: & lt;100 & Omega; CROSSTALK: & lt;-118 dBu @ 1kHz & 10kHz FREQUENCY RESPONSE: & plusmn;0.5 dB 10Hz to Fs/2 (Nyquist) CROSSTALK: -115dBu @ 1kHz & 10kHz THD+N @ -1dBFS (1kHz): & lt;0.0006% (-104dB) DYNAMIC RANGE: 124 dB un-weighted, 126 dB A-weighted 1/4 & rdquo; TRS JACK: TIP (Hot), RING (Cold) & SLEEVE (Shield) Headphone Outputs: (Measured under AES-17 at phones output) MAXIMUM OUTPUT LEVEL: +14 dBu (0 dBFS digital maximum) DIGITAL REFERENCE LEVEL: +14 dBu = 0 dBFS OUTPUT IMPEDANCE: & lt;50 & Omega; unbalanced CROSSTALK: & lt;-110 dBu @ 1kHz & 10kHz FREQUENCY RESPONSE: & plusmn;0.5dB 10Hz to Fs/2 CROSSTALK: -115dBu @ 1kHz & 10kHz THD+N @ -1dBFS (1kHz): & lt;0.0008% (-103 dB) DYNAMIC RANGE: 121 dB un-weighted, 124 dB A-weighted MAX LEVEL INTO 30ohms: +10.2 dBu 0.002% THD+N Power: 210mW MAX LEVEL INTO 60ohms: +14.2 dBu 0.001% THD+N Power: 54mW MAX LEVEL INTO 600ohms: +14.2 dBu 0.001% THD+N Power: 54mW 1/4 & rdquo; JACK: TIP (Hot), RING (Cold) & SLEEVE (Shield) Digital Input: ADAT 16 CHANNELS: 44.1kHz to 48.0kHz ADAT 8 CHANNELS (SMUX): 88.2kHz to 96.0kHz STEREO S/PDIF: 44.1kHz to 96.0kHz USB2.0 High Speed: No. of INPUT CHANNELS 20: 20 (4 Analogue, 16 Digital) No. of OUTPUT CHANNELS 24: 24 (8 Analogue, 16 Digital) Connector: USB Type-C Included Cables: 1.5m USB 2.0 Type-C to USB Type-C, 1.5m USB 2.0 Type-C to USB Type-A DSP Mixer Latency & ndash; ROUND TRIP (in-to-out): 44.1kHz 0.677ms 48.0kHz 0.625ms 88.2kHz 0.354ms 96.0kHz 0.323ms Unit: 276mm (w) x 51mm (h) x 174mm (d)

Audient Id4 2 In - 2 Out Audio Interface - mkii

Audient iD4 (MKII) 2in | 2out Audio Interface. Every iD interface features the Audient Console Mic Preamp, the same discrete circuit design found in our renowned recording console the ASP8024-HE. Designed to deliver ultra- low noise and low distortion with a touch of classic analogue warmth, iD4 & rsquo;s Audient mic pre will give you the professional sound you deserve. iD4 & rsquo;s converters make sure you hear every nuance, every detail of your audio, letting you hear your mix more accurately. Work faster, make better creative decisions and experience professional audio performance from your desktop. Equipped with both a jack and mini jack connection and a powerful headphone amp capable of driving headphones up to 600Ohms, iD4 is ready to take on the most demanding recording sessions. Designed to replicate the input stage of a classic valve amplifier, iD4 & rsquo;s harmonically rich JFET Instrument Input is the perfect sonic foundation for your guitar or bass. D.I / Instrument Input RANGE: 40dB LINEUP: 12dBu = 0dBFS THD+N @ 0dBu: 0.1% SNR: 100dBu A-Weighted FREQUENCY RESPONSE & ndash; MIN GAIN & plusmn;0.5dB 10Hz to 20kHz Microphone preamplifier GAIN RANGE: 58dB LINEUP: 12dBu = 0dBFS MIC MAX INPUT LEVEL: 12dBu MAX INPUT LEVEL: 21dBu INPUT IMPEDANCE (Mic): 2.8k INPUT IMPEDANCE (Line): & gt;8k THD+N @ 0dBu 0.00170% THD+N @ 0dBu MAX GAIN: & lt;0.04% SNR: 101dBu A-Weighted EIN: 129dB A-Weighted CMRR @ 1k: & gt;75dB FREQUENCY RESPONSE & ndash; MIN GAIN & plusmn;0.5dB 10Hz to 40kHz Analogue to Digital Converter THD+N @ -1dBFS: 0.001% DYNAMIC RANGE: 120dB A-Weighted FREQUENCY RESPONSE: & plusmn;0.5dB 10Hz to 40kHz Line Outputs (DAC): LINEUP: 12dBu = 0dBFS THD+N @ -1dBFS: 0.0006% DYNAMIC RANGE: 125.5dB A-Weighted CROSSTALK: & gt;120dB FREQUENCY RESPONSE: & plusmn;0.1dB 10Hz to 40kHz 1/4 & rdquo; TRS JACK: Tip (Hot), Ring (Cold) & Sleeve (Shield) Headphone Outputs: LINEUP: 18dBu = 0dBFS THD+N @ -1dBFS: 0.0009% DYNAMIC RANGE: 125.5dB A-Weighted CROSSTALK: & gt;116dB FREQUENCY RESPONSE: & plusmn;0.1dB 10Hz to 40kHz MAXIMUM LEVEL @ 30R: 2.59V Peak, 1.827V RMS, 223mW MAXIMUM LEVEL @ 62R: 4.18V Peak, 2.95V RMS, 280mW MAXIMUM LEVEL @ 600R: 7.72V Peak, 5.46V RMS, 100mW 1/4 & rdquo; TRS JACK: Tip (Left), Ring (Right) & Sleeve (Shield) USB-C High Speed: BUS POWER: MIN REQUIREMENT: 0.9A @ 5V & gt;=USB 3.0 Port MAX REQUIREMENT: 1.5A @ 5V USB-C: Provides higher headphone outputs levels No. of INPUT CHANNELS: 2 (2 Analogue) No. of OUTPUT CHANNELS: 2 (2 Analogue) DSP MIXER LATENCY ROUND TRIP (in-to-out): 44.1kHz 0.65mS 48.0kHz 0.6mS 88.2kHz 0.33mS 96.0kHz 0.31mS

Aqa S5 Recording Microphone Wind Screen Board 5 Panels Sound-absorbing

Portable design, five-panel combination, adjustable angle, easy to carry out, easy to install Porous ABS shell, sturdy design, effectively reduces the impact of noise on the recording effect Multi-layer noise reduction, the sound is clearer, effectively preventing the interference of external noise to the microphone Acoustic principle design, high-density sponge, prevent sound emission from being absorbed by the microphone, reduce diffuse sound waves Can be placed on a desktop or mounted on a stand (not included)- Item model number: S5 Material: ABS Size: 75*4.5*32.5cm Package included: 1 x Microphone Wind Screen Board 1 x Screw Pack Other items not include

Keylab Essential 88 Controller

Item Weight 19.84 pounds Product Dimensions 53.54 x 12.6 x 4.72 inches ASIN B083XM25GY Item model number 230541 Customer Reviews 4.5 out of 5 stars Best Sellers Rank #7,696 in Musical Instruments ()#40 in Date First Available February 5, 2020 Color Name White Connector Type MIDI USB Number of Keyboard Keys 88 The perfect combo of intuitive control and artistic inspiration.A controller with powerful functionality, a great-feeling piano-sized keybed, and a layout that & rsquo;s easy to master.KeyLab Essential comes with Analog Lab, Arturia & rsquo;s multi-award-winning software suite that gives you access to thousands of incredible synth and keyboard sounds. Sourced from every instrument contained within the Arturia V Collection, Analog Lab is like being given the keys to your very own keyboard museum, packed with the iconic analog monosynths, illustrious and exotic pianos, and classic organs, digital workstations, and much more. Each one of the many thousands of presets has forged by some of the world & rsquo;s finest sound designers, and catalogued in a clever, tag-based archive. Finding the perfect sound for your song has never been easier. KeyLab Essential has the iconic keyboard sounds you need to take your music to the next level. Analog Lab gives you VIP access to the most coveted keyboards ever created, brought back to life by Arturia & rsquo;s exclusive True Analog Emulation & trade; technology.Whether you need a searing-hot synth lead or an ethereal string pad, a vintage upright piano or a complex, animated soundscape, KeyLab Essential gives you everything you need and more.KeyLab Essential is simple yet highly effective, a launchpad into the exciting world of music performance and production for newcomers, and a powerful, ergonomic control solution that experienced users will love.

Aqa S3 Microphone Isolation Shield - High Density Absorbent Foam - 3 Folding

Portable design, three-panel combination, adjustable angle, easy to carry out, and easy to install Porous new ABS shell, a sturdy design, effectively reduces the impact of noise on the recording effect Multi-layer noise reduction, the sound is clearer, and effectively prevents the interference of external noise to the microphone Acoustic principle design, high-density sponge, prevent sound emission from being absorbed by the microphone and reduce diffuse sound waves It can be placed on a desktop or mounted on a stand Applicable places: personal recording studio, professional recording studio, stage, chat room, Internet cafe, broadcasting room, control room Scope of application: computer recording production, cover recording, online K song, video chat, broadcasting, radio hosting

Native Instruments Maschine Mikro

Native Instruments MASCHINE MIKROMeet MASCHINE MIKRO, your flexible, compact companion for making music with a laptop. Use it to tap out beats, play melodies, and build up tracks & ndash; fast, fun, and hands-on. Want to start creating right away? We & rsquo;ve thrown in everything you need including instruments, sounds, effects, and powerful tools like sampling and drum synths. YOUR COMPACT BEATMAKING COMPANION Make beats, play melodies, and build tracks hands-on & ndash; in the studio or on the go Fast, flexible hardware/software instrument & ndash; use on its own or with any DAW Play with inspiring sounds and effects for any style, including full versions of MASSIVE, MONARK, and REAKTOR PRISM The most affordable MASCHINE ever DRUM IT. PLAY IT. SKETCH IT. MIKRO gives you four different ways of getting hands-on with your music using the 16 pads. Drum beats in Pad mode, with color coding for kicks, snares, and other sounds. Switch to Keyboard mode to play melodies with the pads. In Chord mode, it & rsquo;s easy to lay down inspiring chord progressions. And in Step mode, program beats and patterns visually in a classic step-sequencer style on the 16 pads & ndash; get exciting musical results quickly. PLAY WITH SOUNDS IN NEW WAYS Add creative flourishes to your beats and melodies with the Smart Strip. Slide your fingers to bend sounds, strum instruments, or go wild with Perform FX like Stutter and Echo. PLAY WITH INSPIRING SOUNDS AND FX You & rsquo;ll find inspiration using the selection of premium sounds, samples, instruments, and FX included with MASCHINE MIKRO. Plus it comes with full versions the popular synths MASSIVE, MONARK, and REAKTOR PRISM, as well as the free KOMPLETE START. Then when you & rsquo;re ready for more juice, simply upgrade to the MASCHINE Factory Library, or KOMPLETE 12 Select, and get more top-notch sounds, while making a tidy saving. FEATURES AND SPECIFICATIONS Compact, music production instrument that integrates powerful software with tactile, responsive hardware Four ways to input sound using the 16 pads & ndash; drum in pad mode, play melodies in Keyboard mode, create chord progressions in Chord mode, and program in a classic step-sequencer style from Step mode Use the software on its own or as a VST, Audio Unit, or AAX plug-in in all major DAWs (including Ableton Live, Pro Tools, Logic Pro, and FL Studio) 1.6 GB MASCHINE Factory Selection with samples, one-shots, loops, sample instruments, presets, patterns, drum kits, and songs Same software as MASCHINE MK3 / STUDIO / JAM & ndash; includes 25 pro-quality studio and creative FX including filter, EQ, delay, reverb, and compressor 16 large, velocity-sensitive pads for easy two-handed drumming Dual-touch Smart Strip lets you slide your fingers to strum instruments, bend sounds, use Perform FX, and more Push encoder and screen for browsing, navigating, adjusting volume levels and panning, and controlling parameters Powered via USB 2.0 Classic groovebox features including 16 pad velocity levels, swing, pad link, note repeat, step sequencer, and vintage MPC60/SP1200 sampling emulation Powerful mixer, arranger, and sampler for full creative control over your tracks A doorway into the Native Instruments sound universe & ndash; easily expand your library with KOMPLETE, Sounds.com, Expansions, and enjoy perfect integration with any third party NKS-certified instruments and effects

Conference Microphone With Volume Button

This microphones cartridge is high-quality condense, match with deeply controlled circuits, this microphone has ultra cardioid polar Pattern and high sensibility and also match with the circuit which can remove the noise when turn the on-off switch. this Elegance condenser is a popular choice for use in professional audio convention halls, speedy meeting. This professional microphone condenser comes with volume button which will help you to control the volume.

Arturia Keystep Controller

Colour Not Applicable Arturia & rsquo;s own Slimkey keybed with velocity and aftertouch Arpeggiator mode: Up, Down, Inclusive, Exclusive, Random, Walk, Pattern and Order Sequencer mode: 8 polyphonic step-sequences with Rest, Tie, and Legato note entry Rate control and tap tempo: REC, PLAY, and STOP buttons for performance control over the sequencer and arpeggiator Octave controls for keyboard and arpeggiator Sustain HOLD button Sustain pedal jack Chord play mode SHIFT button selection: MIDI channel selection, GATE time, SWING values DC jack for standalone operation USB MIDI connects to computers and our MCC editor MIDI in/out ports Sync i/o ports: Supports 1 pulse per step, 2 PPQ (Korg Volca), 24 PPQ DIN sync, 48 PPQ DIN sync Sync select switches: Internal, USB, MIDI, Clock CV/GATE outputs: CV supports 1Volt per octave, Volt & gt;Hz modes, Gate output 5V or 12V for modern or vintage gear support CV Velo/Aftertouch/Modwheel output Capacitive-touch pitch bend and mod wheels Each sequence can have 64 steps, each step can have up to 8 notes Low power; can be powered by Apple iPad & reg; (camera connection kit required)

Tech Odl-312 Digital Audio Interface

Brand Hosa Tech Odl-312 Digital Audio Interface The ODL-312 Digital Audio Interface by Hosa Technology allows simultaneous transfer between S/PDIF optical and AES/EBU digital audio formats. It is ideal for interconnecting digital audio workstations, recorders, and other digital audio gear regardless of I/O format. Features include: & bull; Two channels S/PDIF optical to AES/EBU and vice versa & bull; Simultaneous conversion in both directions if required & bull; Support for 24-bit/96 kHz S/PDIF audio & bull; AC adaptor included One piece of digital audio gear may have only S/PDIF optical (Toslink) connections while another may have only AES/EBU connections (XLR). With the ODL-312, transfers between the two formats remain in the digital realm. The ODL-312 is an indispensable tool for the digital audio recordist! SCMS (Serial Copy Management System) is disabled when transferring from S/PDIF to AES/EBU. This unit is incompatible with the ADAT Optical Interface.

Presonus Bluetube Dp V2 Micinstrument Preamp

The BlueTube DP V2 dual-path mic/instrument preamplifier which is compact, affordable, and capable of a stunningly wide range of tones, offers two independent channels, each with an XMAX Class A solid-state preamp, followed in the signal path by a 12AX7 vacuum-tube stage. A Tube Drive control provides a wide range of sounds: When clicked off, you & rsquo;re using the solid-state preamp for quiet, transparent amplification; when engaged, your signals flow through the tube preamp, and you can achieve anything from gentle warmth to edgy distortion. Equipped with instrument and mic inputs and built tough for serious gigging, the BlueTube DP V2 is a great choice for guitarists, bassists, singer/songwriters, and more. The BlueTube DP v2 from PreSonus is a two-channel microphone/instrument preamplifier with "Dual Path" technology that delivers the best of both worlds. It offers a solid state preamplifier stage and a tube preamplifier stage in each channel, delivering either fat, warm tube tone, or solid state transparency. When the Tube Drive is clicked off, the tube preamplifier stage is bypassed delivering ultra-quiet pre-amplification. When it's engaged, the signal flows through the tube preamp providing anything from gentle warmth to edgy distortion. The solid-state path feeds the company's Class A XMAX microphone preamp with 80 dB of variable gain, while the tube path features a 12AX7 tube that operates on higher voltages than comparable models, producing lots of headroom. Each channel of the unit includes a -20dB pad, phase reverse, 80 Hz filter, and +48 V phantom power. Controls include a solid state GAIN control and switchable on/off Tube Drive. The front panel includes illuminated analog VU meters for each channel for easy visual monitoring. The preamp is great for enhancing all types of microphones including condensers, dynamics and ribbons, as well as instruments including keyboards, acoustic and electric guitars and bass. It also serves as a DI box, thanks to balanced XLR and unbalanced 1/4" outputs. Singer-songwriters can run their vocals through one channel and a guitar through the other, feeding both to a PA system. Housed in a rugged half-rack enclosure, the preamp can be used as a desktop unit, or can be screw-mounted to a standard rack tray. Two-channel "Dual Path" microphone/instrument preamp High headroom Class A XMAX microphone preamp with 80 dB gain range 12AX7 vacuum tube gain stage Tube Drive tube-saturation control 20 dB pad, phase reverse and 80 Hz filter on each channel 48 VDC phantom power Two illuminated analog VU meters Functions as a DI for bass and guitar

Audient Id44 - mkii - 20in 24out Audio Interface

Audient iD44 (MKII) 20in | 24out Audio Interface Integrate your favourite outboard FX prior to conversion and start creating signal chains that rival the very best. The insert returns also gives you direct access to the A/D converters providing the cleanest signal path possible, making it great for print-backs or integrating outboard line level sources. Designed to replicate the input stage of a classic valve amplifier, iD44 features two harmonically rich JFET Instrument Inputs giving you the perfect sonic foundation for your guitars or basses before you hit your amp sims. Connect and listen to your mixes through two sets of speakers with iD44 & rsquo;s four line outputs. Alternatively use the extra line outputs to send audio to an external headphone amp for distribution to your artists. Easily record and collaborate with others by utilising iD44 & rsquo;s two individual stereo headphone amps, both providing more than enough power for your headphones to perform accurately. Now equipped with Audio Loop-back, iD44 can quickly transform into a multi-purpose powerhouse. Giving you the ability to capture playback from multiple applications on your computer at the same time as your microphones, Audio Loop-back lets you create a custom audio feed ready to send to your streaming software. Ideal for content creators, podcasters and streamers. iD44 & rsquo;s dedicated talkback technology enables you to use any audio source connected to your computer such as a built-in or USB microphone as your talkback mic, freeing up valuable mic preamps for recording. Specifications Microphone preamplifier MIC GAIN: 0 to +60 dB LINE GAIN: -10 to +50 dB PHANTOM POWER: 48v +/-4v @ 10mA/Channel (12VDC only) MIC EIN: -126dBu CMRR: & gt;80dB @ 1kHz MAXIMUM INPUT LEVEL: +18 dBu INPUT IMPEDANCE (Mic): 3k & Omega; balanced INPUT IMPEDANCE (Line): 10k & Omega; balanced FREQUENCY RESPONSE: & plusmn;0.5 dB 10Hz to 65kHz CROSSTALK: & lt;-90 dBu @ 1kHz & 10kHz THD+N @ 0dBu (1kHz): 0.003% (-96dBu) SNR: 96dB XLR: Pin 2 (Hot), Pin 3 (Cold) & Pin 1 (Shield) 1/4 & rdquo; TRS JACK: TIP (Hot), RING (Cold) & SLEEVE (Shield) D.I / Instrument Input (Channel 1): D.I GAIN: 0 to +60 dB MAXIMUM INPUT LEVEL: +10dBu INPUT IMPEDANCE: 1Meg & Omega; Unbalanced FREQUENCY RESPONSE: & plusmn;0.5 dB 10Hz to 50kHz THD+N @ 0dBu (1kHz): & lt;0.3% SNR: 95dB A-weighted 1/4 & rdquo; JACK: Tip (Hot) & Sleeve (Shield) Analogue to Digital Converter (ADC 1 & 2): (Measured via Insert Returns under AES-17) MAXIMUM INPUT LEVEL: +18 dBu (0 dBFS digital maximum) DIGITAL REFERENCE LEVEL: +18 dBu = 0 dBFS INPUT IMPEDANCE: & gt;10k & Omega; Balanced CROSSTALK: -115 dBu @ 1kHz & 10kHz FREQUENCY RESPONSE: & plusmn;0.5 dB 10Hz to Fs/2 (Nyquist) CROSSTALK: -115dBu @ 1kHz & 10kHz THD+N @ -1dBFS (1kHz): & lt;0.0003% (-112dB) DYNAMIC RANGE: 120 dB A-weighted 1/4 & rdquo; TRS JACK: TIP (Hot), RING (Cold) & SLEEVE (Shield) Digital to Analogue Converter (DAC 1 & 2): (Measured under AES-17 at line outputs 1 & 2) MAXIMUM INPUT LEVEL: +18 dBu (0 dBFS digital maximum) DIGITAL REFERENCE LEVEL: +18 dBu = 0 dBFS OUTPUT IMPEDANCE: & lt;100 & Omega; CROSSTALK: & lt;-118 dBu @ 1kHz & 10kHz FREQUENCY RESPONSE: & plusmn;0.5 dB 10Hz to Fs/2 (Nyquist) CROSSTALK: -115dBu @ 1kHz & 10kHz THD+N @ -1dBFS (1kHz): & lt;0.0006% (-104dB) DYNAMIC RANGE: 124 dB un-weighted, 126 dB A-weighted 1/4 & rdquo; TRS JACK: TIP (Hot), RING (Cold) & SLEEVE (Shield) Headphone Outputs: (Measured under AES-17 at phones output) MAXIMUM OUTPUT LEVEL: +14 dBu (0 dBFS digital maximum) DIGITAL REFERENCE LEVEL: +14 dBu = 0 dBFS OUTPUT IMPEDANCE: & lt;50 & Omega; unbalanced CROSSTALK: & lt;-110 dBu @ 1kHz & 10kHz FREQUENCY RESPONSE: & plusmn;0.5dB 10Hz to Fs/2 CROSSTALK: -115dBu @ 1kHz & 10kHz THD+N @ -1dBFS (1kHz): & lt;0.0008% (-103 dB) DYNAMIC RANGE: 121 dB un-weighted, 124 dB A-weighted MAX LEVEL INTO 30ohms: +10.2 dBu 0.002% THD+N Power: 210mW MAX LEVEL INTO 60ohms: +14.2 dBu 0.001% THD+N Power: 54mW MAX LEVEL INTO 600ohms: +14.2 dBu 0.001% THD+N Power: 54mW 1/4 & rdquo; JACK: TIP (Hot), RING (Cold) & SLEEVE (Shield) Digital Input: ADAT 16 CHANNELS: 44.1kHz to 48.0kHz ADAT 8 CHANNELS (SMUX): 88.2kHz to 96.0kHz STEREO S/PDIF: 44.1kHz to 96.0kHz USB2.0 High Speed: No. of INPUT CHANNELS 20: 20 (4 Analogue, 16 Digital) No. of OUTPUT CHANNELS 24: 24 (8 Analogue, 16 Digital) Connector: USB Type-C Included Cables: 1.5m USB 2.0 Type-C to USB Type-C, 1.5m USB 2.0 Type-C to USB Type-A DSP Mixer Latency & ndash; ROUND TRIP (in-to-out): 44.1kHz 0.677ms 48.0kHz 0.625ms 88.2kHz 0.354ms 96.0kHz 0.323ms Unit: 276mm (w) x 51mm (h) x 174mm (d)

Solo Usb Heritage Edition

Brand Apollo Solo USB Heritage Edition Ready for cranking out tracks at home or on the road with your Windows computer, the Universal Audio Apollo Solo USB Heritage Edition desktop 2x4 USB 3.0 Type-C audio interface combines the sound, feel, and flow of analog studio recording with SOLO Core real-time UAD processing and a hearty bundle of 25 stellar UAD plug-ins. Furnished with studio-class 24-bit / 192 kHz conversion, the Apollo Solo USB gives musicians, producers, and songwriters the appreciable value of high-resolution recording and mixing with distortion and dynamic performance beyond its price point. The interface features two XLR-1/4" mic/line combo inputs and a 1/4" Hi-Z input, all with Unison integration for precise UAD emulations of classic analog preamps. Impart vintage character of your choosing on microphone and instrument recordings while bypassing the unpredictable nature of old equipment. Thanks to the switchable low-cut filter, pad, polarity inversion, 48V phantom power, and stereo linking on each analog input, you can efficiently optimize your incoming signals with straightforward buttons on the Apollo Solo USB's face. It offers a dedicated stereo monitor feed and a front-panel headphone output, plus full input and output metering capabilities. The built-in SOLO Core processing allows you to monitor and record audio using classic analog emulations with near-zero latency. The plug-in bundle included with the Heritage Edition empowers you with 25 top-notch plug-ins ranging from vintage compressor and EQ collections to virtual guitar/bass amps and time-based processors. The included Console application provides control and recall of all interface and UAD plug-in settings including channel-strip presets, drag-and-drop functionality, and dynamically resizable windows. Please note, the Apollo Solo USB requires an external power supply (included) and a USB 3.0 port on your computer in order to operate. To see if your computer is compatible with the Apollo Solo USB, refer to the manufacturer website for compatibility information. Heritage Edition The Heritage Edition features the same Apollo Solo USB interface found in the standard edition but with more plug-ins. The standard Apollo Solo USB includes the Realtime Analog Classics bundle (14 plug-ins) and the Heritage Edition adds 11 more plug-ins for a total of 25 revered UA powered plug-ins. UA Sound in a Portable Form Track, overdub, and mix with high-resolution AD/DA conversion and DSP-powered plug-ins UAD-2 SOLO Core processing for tracking through models of vintage compressors, EQs, tape machines, mic preamps, and guitar amps, with near-zero latency, and no burden on your computer & rsquo;s CPU Unison technology nails the tone of sought-after tube and solid-state mic pres by matching the input impedance, gain-stage sweet spots, and component-level circuit behaviors of the original hardware High-speed USB 3.0 Type-C connectivity Windows computers (USB SuperSpeed cable available separately) Convenient desktop form factor with an external power supply Comprehensive front-panel metering and fast, intuitive controls; no menu-diving is required Free, industry-leading phone/online technical support from knowledgeable audio engineers I/O for the Home Studio 2x4 audio interface with two Unison-enabled microphone preamps (via XLR-1/4" combo mic/line inputs), providing emulations of classic analog preamps with near-zero latency One front-panel Unison-enabled 1/4" Hi-Z input for direct connection of a guitar, bass, or keyboard Stereo 1/4" monitor output and one 1/4" headphone output, each with dedicated level control 25 Powered Plug-Ins Includes Realtime Analog Classics plug-in bundle plus 11 additional plug-ins to complete the compressor, EQ, and preamp collections and provide another reverb (plug-ins support VST, RTAS, Audio Units, and AAX 64-bit for compatibility with all major DAWs): UA 610-A Tube Preamp and EQ (Vintage) UA 610-B Tube Preamp and EQ (Modern) Marshall Plexi Classic Guitar Amp Ampeg SVT-VR Classic Bass Amp UA 1176LN Limiting Amplifier (Legacy) UA 1176SE Limiting Amplifier (Legacy) UA 1176 Classic Limiter Collection (1176LN Rev E, 1176 Rev A, and 1176AE 40th Anniversary Edition) Pultec EQP-1A EQ (Legacy) Pultec MEQ-5 EQ (Legacy) Pultec Passive EQ Collection (EQP-1A, MEQ-5, and HLF-3C) Teletronix LA-2A Leveling Amplifier (Legacy) Teletronix LA-2A Classic Leveler Collection (LA-2A Silver, LA-2A Gray, and LA-2) Raw Distortion Precision Channel Strip (Precision Mix Rack Collection) Precision Reflection Engine (Precision Mix Rack Collection) Precision Delay Mod (Precision Mix Rack Collection) Precision Delay Mod L (Precision Mix Rack Collection) Pure Plate Reverb RealVerb Pro Custom Room Modeler

Vocal Booth

Booth helps to control what goes on around the microphone as much as possible by isolating the microphone from outside world and eVocal nsuring that sound that sound does not bounce around and back into the microphone. Are you looking for a top quality, yet affordable soundproofing solution for your vocal recordings? Then look no further than this studio microphone isolation shield enclosure! Boasting a strong, metal shell with 5 acoustic foam panels that will block off outside noise, such as air conditioning or computer fans, reduce sound reflections or echo and attenuate unwanted acoustic interference, this soundproof filter will let you record like a pro

Nektar Impact Gx Mini Keyboard

Musicians, producers, and DJs looking for a small, ultraportable MIDI keyboard controller will be pleased with the Nektar Impact GX Mini, a 25-note mini-key keyboard with velocity and DAW integration. The updated keybed offers expressive performance with a defined and firm feel. Additionally, the keyboard response can be adjusted to your playing style thanks to three available velocity curves. The combination pitch bend and modulation joystick can be reprogrammed to any CC message allowing you to control whatever parameters you need. The Impact GX Mini features eight dedicated buttons, putting essential DAW functions right at your fingertips. Control transport, track navigation and loads of other features with Nektar DAW Integration. All buttons are MIDI assignable for use with any software that's not directly supported. A notable feature is the included Part 2, which allows you to shift the octave up or down, transpose, layer another octave on top, or switch to another MIDI channel in real-time while playing. What's more, once you release the Part 2 button, the Impact GX Mini reverts to its original settings. A great performance feature. The GX Mini also includes a 3.5mm footswitch input for a sustain pedal. A 3.5mm male to 1/4" female adapter is included, allowing to you connect most standard footswitches without issue. The Impact GX Mini also includes a micro-USB cable and Bitwig 8-Track. 25 velocity-sensitive mini keys 3 velocity curves (standard, soft, hard) Joystick for pitch bend and 2 modulation controls (MIDI assignable) 1/8" jack for footswitch (adapter included) Octave up/down buttons with LED indicators Part 2 LED buttons (assignable to real-time keyboard shift up/down, layering MIDI notes (intervals and MIDI channels) 7 transport buttons for DAW integration or MIDI assignable Shift button activates secondary level for a total of 14 accessible button functions Nektar DAW integration support (DAW integration software and Bitwig 8-Track, download upon registration) Nektar DAW Integration for Impact GX Mini currently supports: Ableton Live, Bitwig, Cakewalk, Cubase, Digital Performer, FL Studio, Garageband, Logic, Nuendo, Reaper, Reason, and Studio One. Includes template setup for Pro Tools

Tannoy Reveal 402 70 Watt 4" Bi-amped Ultra-compact Studio Reference Monitor With Tuned Fr

Equipped with a bi-amped, 50W amplifier that powers a 4 & Prime; woofer and a 0.75 & Prime; soft-dome tweeter, the Reveal 402 is designed to ensure maximum power and tonal clarity. It also features adjustable volume and EQ settings to customize the tuning of the speaker to compensate for acoustical deficiencies that may be present in your monitoring environment.Included in the box of each monitor, is a 5 meter 1/8 & Prime; (3.5mm) jack cable. Combined with the AUX Link feature, this allows you to plug into your laptop or portable music player & rsquo;s headphone output and link two Reveal 402 monitors for an instant stereo setup with no need for external interfaces. This is convenient for mixing on-the-go or for times when you just want to listen to some of your favorite music from your mobile device.50 Watt Bi-Amp module and active crossover filter ensures maximum power and tonal clarityBalanced and Unbalanced inputs for maximum flexibilityAdjust volume and EQ to match your listeningRubber padded base for acoustical isolationAccurately tuned front-firing bass port -allows near-wall placement and ensures optimal LF performanceTechnical DetailsProduct Dimensions & lrm;21.01 x 14.5 x 24.51 cm; 4.4 KilogramsItem model number & lrm;REVEAL402Speaker Amplification Type & lrm;ActiveCountry Produced In & lrm;ChinaOutput Wattage & lrm;70Power Source & lrm;Corded ElectricVoltage & lrm;100Wattage & lrm;50 wattsItem Weight & lrm;4.4 kgWhat's in the boxTannoy Reveal 402 4 & Prime; 50W Active Studio Monitor (Pair)5m 1/8 & Prime; (3.5mm) Jack CableLimited 1-Year Warranty

Audient Id14 10 In - 6 Out Audio Interface - Mkii

Audient iD14 (MKII) 10in | 6out Audio Interface. Designed to take your recordings to the next level in every way, the iD14 (MKII) delivers professional audio performance in a compact and modern desktop package, giving you everything you need to make studio quality recordings at home. Every iD interface features the Audient Console Mic Preamp, the same discrete circuit design found in our renowned recording console the ASP8024-HE. Designed to deliver ultra- low noise and low distortion with a touch of classic analogue warmth, iD14 & rsquo;s two Audient mic pre & rsquo;s will give you the professional sound you deserve. The Audient mic pre is a high grade hybrid discrete and op amp design that delivers a clean, accurate and detailed translation of your source. With a noise floor 30,000 times quieter than the signal level your recordings will be captured with stunning clarity. iD14 & rsquo;s converters make sure you hear every nuance, every detail of your audio, enabling you to take your recordings to the next level. Offering an incredible 126dB of dynamic range you will hear your audio more accurately, make better creative decisions and experience stunning clarity directly from your desktop. Plan for the future with iD14 & rsquo;s digital input. Supporting both ADAT and SPDIF, iD14 gives you the option to add up to eight extra mic pre inputs letting you expand your rig and take on larger sessions. D.I / Instrument Input RANGE: 40dB LINEUP: 12dBu = 0dBFS THD+N @ 0dBu: 0.1% SNR: 100dBu A-Weighted FREQUENCY RESPONSE & ndash; MIN GAIN & plusmn;0.5dB 10Hz to 20kHz 1/4 & rdquo; TS JACK: Tip (Hot) & Sleeve (Shield) Microphone preamplifier GAIN RANGE: 58dB LINEUP: 12dBu = 0dBFS MIC MAX INPUT LEVEL: 12dBu MAX INPUT LEVEL: 21dBu INPUT IMPEDANCE (Mic): 2.8k INPUT IMPEDANCE (Line): & gt;8k THD+N @ 0dBu 0.00170% SNR: 101dBu A-Weighted EIN: 129dB A-Weighted CMRR @ 1k: & gt;75dB CROSSTALK: & gt;-100dB FREQUENCY RESPONSE & ndash; MIN GAIN & plusmn;0.5dB 10Hz to 40kHz XLR COMBI FEMALE: Pin 2 (Hot), Pin 3 (Cold) & Pin 1 (Shield) 1/4 & rdquo; TRS JACK: Tip (Hot), Ring (Cold) & Sleeve (Shield) Analogue to Digital Converter THD+N @ -1dBFS: 0.001% DYNAMIC RANGE: 120dB A-Weighted CMRR: & gt;80dB FREQUENCY RESPONSE: & plusmn;0.5dB 10Hz to 40kHz Line Outputs (DAC): LINEUP: 12dBu = 0dBFS THD+N @ -1dBFS: 0.0006% DYNAMIC RANGE: 125.5dB A-Weighted CROSSTALK: & gt;120dB FREQUENCY RESPONSE: & plusmn;0.1dB 10Hz to 40kHz 1/4 & rdquo; TRS JACK: Tip (Hot), Ring (Cold) & Sleeve (Shield) Headphone Outputs: LINEUP: 18.5dBu = 0dBFS THD+N @ -1dBFS: 0.0009% DYNAMIC RANGE: 125.5dB A-Weighted CROSSTALK: & gt;116dB FREQUENCY RESPONSE: & plusmn;0.25dB 10Hz to 40kHz MAXIMUM LEVEL @ 30R: 2.59V Peak, 1.827V RMS, 223mW MAXIMUM LEVEL @ 62R: 4.18V Peak, 2.95V RMS, 280mW MAXIMUM LEVEL @ 600R: 7.72V Peak, 5.46V RMS, 100mW 1/4 & rdquo; TRS JACK: Tip (Left), Ring (Right) & Sleeve (Shield) USB-C High Speed: BUS POWER: MIN REQUIREMENT: 0.9A @ 5V & gt;=USB 3.0 Port MAX REQUIREMENT: 1.5A @ 5V USB-C: Provides higher headphone outputs levels No. of INPUT CHANNELS: 10 No. of OUTPUT CHANNELS: 16 DSP MIXER LATENCY ROUND TRIP (in-to-out): 44.1kHz 0.65mS 48.0kHz 0.6mS 88.2kHz 0.33mS 96.0kHz 0.31mS

Universal Audio 710tfd Twin-finity Single-channel Microphone Preamp

Universal Audio 710tfd Twin-finity Single-channel Microphone Preamp Twin-Finity & trade; Tone-Blending Mic/Line Preamp & Hi-Z Instrument DIDual-Path 310 volt Class-A Tube and Transimpedance Solid State PreampPhase-Aligned & ldquo;Tone-Blending & rdquo; of Tube and Solid StateDual Gain Stages: Wire with Gain to Creamy to CrunchyDiscrete JFET DI with 2.2M ohm Ultra Hi-Z impedanceMonolithic Balanced Output Stage70dB+ of gain, +48V Phantom, Pad(-15dB), Phase Invert, and Low Cut Filter(75Hz)Output and & ldquo;Drive & rdquo; backlit VU meteringPortable, Rack-Mountable design for Studio, Desktop or Stage19 & rdquo; Rack Kit IncludedFront Panel Hi-Z Input (switched from Mic/Line automatically via Jack Detect)Rear Panel XLR Mic Input, XLR Line Input and XLR Line OutputUniversal Internal Power SupplyHeavy-Duty Metal Construction Specifications InputsMicrophone (Female XLR)Balanced Line (Female XLR)Unbalanced Instrument (1/4 & Prime; jack) (D.I.)OutputsBalanced Line (Male XLR)Tube Complement12ax7Pad-15dBHigh Pass Filter75HzMaximum Power Consumption160mA @120VAC, 20WPower Requirements100-240VACDimensions8.45W x 3.5H x 10.25DWeight5.25 lbImpedanceMic Input Impedance2K ohmsLine Input Impedance10K ohmsHi-Z Input Impedance2.2M ohmsInternal Output Impedance600 ohmsGain/LevelsGain Range for Unit-Infinity to 70dBuMic Range Gain Pot10 ~ 60 dBuLine Range Gain Pot-10 ~ 40 dBuHi-Z Range Gain Pot-10 ~ 40 dBuFrequency ResponseMic Frequency Response20Hz to 100kHz +/- 0.2 dBuLine Frequency Response20Hz to 100kHz +/- 0.2 dBuHi-Z Frequency Response20Hz to 100kHz +/- 0.2 dBuDistortionMin THD+Noise @ +4dBU

Nektar Panorama P6 – Keyboard Controller

Spectacular and deep integration with Bitwig Studio, Cubase, Logic Pro, MainStage, Reaper and Reason puts the spotlight on performance and creativity. Keyboard and pads are dynamic, sensitive and balanced carefully with a solid feel that allows for complete expression. All this, combined with 93 real-time controls available at any one time, makes Panorama the definitive keyboard controller for Bitwig Studio, Cubase, Logic Pro & Reason. PORTS & CONNECTIONS On the back of Panorama you find the connection points you need for foot controls, power and data including: USB Micro B for external power supply or additional power for the motorized fader (cable included) USB port for power and data connection to your computer 5-pin MIDI din output port sending data either directly from the unit or from your DAW (working like a MIDI interface) Foot switch jack, assignable (pedal not included) Expression pedal jack, assignable (pedal not included) On/off switch KEYBOARD BALANCED TO PERFECTION Panorama & rsquo;s keyboard action uses weights to offset the otherwise increasing tension you would experience from the spring. This means the down movement is as clean as possible and not heavy or fatiguing to play. We keep the down weight required within the heavy end of common standards for acoustic pianos. In addition, the dynamic range is much wider than what you experience on most controller keyboards allowing better control of both low and high velocity values. 5 velocity curves gives you choice just in case your playing style requires a different feel. Monophonic aftertouch, pitch bend and modulation wheels, plus foot switch and expression pedal jacks set you up for performance. THE DISPLAY SAYS IT ALL A crystal clear 3.5 & Prime; color TFT display delivers the information you really need, for each mode or menu. Regardless of whether you are operating Reason or programming MIDI assignments in Internal mode, the display provides detailed information that makes your workflow fluent and fast. Panorama takes the hard work out of using a controller and makes operations that seem complicated and non-transparent on other products, straight-forward and simple. MORE CONTROLS THAN EVER BEFORE An unrivaled amount of assignable controls makes Panorama the most comprehensive and fully featured MIDI controller keyboard around. 16 encoders, 9 45mm faders, 1 100mm motorized ALPS fader, 10 LED buttons, 28 buttons, 12 pads each with strike and pressure component, foot switch jack, expression pedal jack, keyboard after touch, pitch bend and modulation wheels gives you immediate control of up to 93 parameters at any one time. You can store settings in 20 presets with individually savable and loadable keyboard-, pad- and F-keys-maps. We could argue that it gives you access to over 1500 assigned controls, but that would be spinning it too far. MIDI CONTROL & ndash; A GAME OF MANY OPTIONS! Setting up presets or F-keys maps is easy on Panorama. The Control Edit menu enables you to quickly select a control and assign the MIDI command you want in real-time. For each control, values can be scaled, reverse and assigned specific or global MIDI channels. Here is a chart showing the programming options available for each type of control: PRO-CONSOLE CONTROL WITHIN REACH The motorized 100mm touch-sensitive ALPS fader gives you pro-console mixer channel control when operated with Bitwig, Cubase, Logic, Nuendo, Reaper or Reason. Watch the fader move when you change tracks and just move it to change volume. Two LED buttons control Solo and Mute & ndash; so no matter what mode you are operating Panorama in, you always have pro-console control within reach. TRANSPORT WHEN YOU NEED IT,FUNCTION BUTTONS WHEN YOU DON & rsquo;T It & rsquo;s hard to go places without transport, so Panorama features an extended 11 button transport bar, positioned right where you need it: Return to L, Forward to R, Undo, Click on/off, Record Mode, Cycle on/off, Back, Forward, Stop, Play and Record. Using the shift button, these also double up as 11 function buttons each assignable to MIDI commands or QWERTY macro & rsquo;s. SHORTCUT TO SOFTWARE FUNCTIONS* So QWERTY macro & rsquo;s & hellip; & hellip; big deal, right? That & rsquo;s right, its a VERY big deal. Your software has a ton of features and functions that can be activated using QWERTY shortcut commands. Assigning a command to a button, so you don & rsquo;t have to be near your computer, makes life a lot easier. Assigning a string of up to 8 commands takes it to another level. With this powerful feature you could for example enter edit mode, zoom in and select a tool with just one button press. Or create an instrument or effects track and locate a folder containing your presets so you can select them from Panorama, all with one button press and without looking at your computer. *QWERTY macro & rsquo;s are not available in OS X 10.11 or higher CONTROLLING BITWIG STUDIO, CUBASE, NUENDO, LOGIC PRO, MAINSTAGE, REAPER, REASON AND STUDIO ONE HAS NEVER FELT SO REAL For Bitwig Studio, Cubase, Nuendo, Logic Pro, Reaper Reason and Studio One users, Panorama is a dream come true. The dedicated communication protocol ties Panorama and your DAW tightly together, so all you have to do is select the mode and menu you want to control. Panorama does the rest. It is just one button press to switch between controlling the Mixer, Instruments and Transport thanks to Panorama & rsquo;s mode buttons, with the 4th mode, Internal, still providing access to traditional MIDI control. The integration with Bitwig Studio, Cubase, Nuendo, Logic Pro, MainStage, Reaper, Reason and Studio One is so deep that you can immerse yourself in your music without having to constantly reach for the mouse. Panorama gives you the creative freedom to just focus on your music.

Audient Id4 2 In - 2 Out Audio Interface - Mkii

Audient iD4 (MKII) 2in | 2out Audio Interface. Every iD interface features the Audient Console Mic Preamp, the same discrete circuit design found in our renowned recording console the ASP8024-HE. Designed to deliver ultra- low noise and low distortion with a touch of classic analogue warmth, iD4 & rsquo;s Audient mic pre will give you the professional sound you deserve. iD4 & rsquo;s converters make sure you hear every nuance, every detail of your audio, letting you hear your mix more accurately. Work faster, make better creative decisions and experience professional audio performance from your desktop. Equipped with both a jack and mini jack connection and a powerful headphone amp capable of driving headphones up to 600Ohms, iD4 is ready to take on the most demanding recording sessions. Designed to replicate the input stage of a classic valve amplifier, iD4 & rsquo;s harmonically rich JFET Instrument Input is the perfect sonic foundation for your guitar or bass. D.I / Instrument Input RANGE: 40dB LINEUP: 12dBu = 0dBFS THD+N @ 0dBu: 0.1% SNR: 100dBu A-Weighted FREQUENCY RESPONSE & ndash; MIN GAIN & plusmn;0.5dB 10Hz to 20kHz Microphone preamplifier GAIN RANGE: 58dB LINEUP: 12dBu = 0dBFS MIC MAX INPUT LEVEL: 12dBu MAX INPUT LEVEL: 21dBu INPUT IMPEDANCE (Mic): 2.8k INPUT IMPEDANCE (Line): & gt;8k THD+N @ 0dBu 0.00170% THD+N @ 0dBu MAX GAIN: & lt;0.04% SNR: 101dBu A-Weighted EIN: 129dB A-Weighted CMRR @ 1k: & gt;75dB FREQUENCY RESPONSE & ndash; MIN GAIN & plusmn;0.5dB 10Hz to 40kHz Analogue to Digital Converter THD+N @ -1dBFS: 0.001% DYNAMIC RANGE: 120dB A-Weighted FREQUENCY RESPONSE: & plusmn;0.5dB 10Hz to 40kHz Line Outputs (DAC): LINEUP: 12dBu = 0dBFS THD+N @ -1dBFS: 0.0006% DYNAMIC RANGE: 125.5dB A-Weighted CROSSTALK: & gt;120dB FREQUENCY RESPONSE: & plusmn;0.1dB 10Hz to 40kHz 1/4 & rdquo; TRS JACK: Tip (Hot), Ring (Cold) & Sleeve (Shield) Headphone Outputs: LINEUP: 18dBu = 0dBFS THD+N @ -1dBFS: 0.0009% DYNAMIC RANGE: 125.5dB A-Weighted CROSSTALK: & gt;116dB FREQUENCY RESPONSE: & plusmn;0.1dB 10Hz to 40kHz MAXIMUM LEVEL @ 30R: 2.59V Peak, 1.827V RMS, 223mW MAXIMUM LEVEL @ 62R: 4.18V Peak, 2.95V RMS, 280mW MAXIMUM LEVEL @ 600R: 7.72V Peak, 5.46V RMS, 100mW 1/4 & rdquo; TRS JACK: Tip (Left), Ring (Right) & Sleeve (Shield) USB-C High Speed: BUS POWER: MIN REQUIREMENT: 0.9A @ 5V & gt;=USB 3.0 Port MAX REQUIREMENT: 1.5A @ 5V USB-C: Provides higher headphone outputs levels No. of INPUT CHANNELS: 2 (2 Analogue) No. of OUTPUT CHANNELS: 2 (2 Analogue) DSP MIXER LATENCY ROUND TRIP (in-to-out): 44.1kHz 0.65mS 48.0kHz 0.6mS 88.2kHz 0.33mS 96.0kHz 0.31mS

Arturia Minifuse 2 Flexible Dual Portable Usb Type-c Audio/midi Interface

Arturia MiniFuse 2 Flexible Dual Portable USB Type-C Audio/MIDI Interface MiniFuse 2 is an easy-to-use audio & MIDI interface that gives you pro-grade sound quality, smart connectivity, and a curated selection of the industry & rsquo;s best creative software. From guitar tracking to podcast recording, this is your solution for every type of audio creation. Designed by engineers and gear experts with a passion for sound excellence, MiniFuse 2 is built to answer every audio question you have & ndash; before you & rsquo;ve even asked it. MiniFuse comes with an exclusive selection of software titles offering everything you need to give your sound the professional edge. MiniFuse 2s inputs and outputs bridge the gap between your ideas and the finished product. Record 2 instrument or mic sources simultaneously with dual combo inputs, sync and record your MIDI devices with 5-pin DIN connections, and connect extra devices with the additional USB hub socket - all via universal USB-C computer connectivity. On paper, MiniFuse 2 gives you a 110dB dynamic range and a top-tier equivalent input noise of -129dB. Put more simply, that means unbelievably great sound that can compete with even the finest studios. Enjoy responsive dynamics, a clear noise-free signal, and quality that you can really feel. MiniFuse 2 is designed to accompany you for those last-minute sessions, quick deadlines, and spontaneous musical moments. Its not only compact and lightweight; its rugged aluminium casing can handle the mobile producers lifestyle. Take your sound with you, wherever you go. Whether you're using a laptop or desktop, MiniFuse can work for you. PC or Mac, connect it and enjoy total recording freedom. Better still, with the MiniFuse Control Center app, you can monitor its inputs, outputs, settings, and firmware updates in one place. Loopback Function for Content Creators, Producers, Musicians, Podcaster Duos MiniFuse 2 - Flexible Dual Audio InterfaceMiniFuse 2 is a next-gen audio & MIDI interface that gives you everything you need to make music and audio your own way. With unmatched sound quality, smart connectivity, and an exclusive music-making software pack, this is a portable audio companion evolved.Get Your Sound Out ThereGet inspired and express yourself through sound whenever & wherever with a portable, fully-loaded, and easy-to-use interface like no other.Whether you're a singer-songwriter, keyboardist, composer, or anything in between, enjoy unmatched sound quality, a smart feature set, and the best software included as standard. MiniFuse 2 lets you sound like you - what are you waiting for?The Best Software IncludedMiniFuse comes with an exclusive selection of software titles offering everything you need to give your sound the professional edge. This isn't a bundle of fremium plugins or demos - this is the same exceptional software used by music and audio professionals worldwide. & bull; Ableton Live Lite & bull; Analog Lab Intro & bull; Arturia FX & bull; Native Instruments GUITAR RIG 6 LE & bull; Auto-Tune Unlimited (3-months free subscription) & bull; Splice Creator Plan (3-months free subscription)Features & bull; Included Arturia instruments - 500 vintage & modern keyboard presets with Analog Lab Intro & bull; Tutorials - Learn recording and music production with MiniFuse, starting with the basics & bull; Exclusive content - Tips, tricks, and advice from industry experts & bull; Dedicated online portal - Access everything you need online in one place & bull; Subscriptions - Complimentary introductions to world-class audio & mixing services & bull; 2 x combos Mic/Inst/Line XLR Inputs with 48V phantom power & bull; 2 x 1/4" TRS balanced line outputs with volume control & bull; 1 x stereo headphone output with volume control & bull; 1 x 5-pin MIDI input 1 x 5-pin MIDI output & bull; 1 x USB2 type A hub (250mA max.) & bull; 1 x stereo virtual loopback channel & bull; USB-C interface compatible with PC and Mac, fully USB 2.0 compatible & bull; Bus-poweredSpecificationsLine InputsInput impedance: 16k & Omega;Maximum input level: +22dBuGain range: 56dBFrequency response 20Hz to 20kHz: +/-0.05dB (min gain)Dynamic range: 110dB typical (A-weighted)THD+N @ 1kHz: -100dB typical (un-weighted)Instrument InputInput impedance: 1M & Omega; on TipMaximum input level: +11.5dBuGain range: 56dBFrequency response 20Hz to 20kHz: +/-0.06dB (min gain)Dynamic range: 110dB typical (A-weighted)THD+N @ 1kHz: -91dB typical (un-weighted)Microphone PreampsInput impedance: 2.5k & Omega;Maximum input level: +9dBuGain range: 56dBEquivalent Input Noise (EIN): -129dB typical (A-weighted)Frequency response 20Hz to 20kHz: +/-0.06dB (min gain)Dynamic range: 110dB typical (A-weighted)THD+N @ 1kHz: -100dB typical (un-weighted)SpeakersOutput impedance: 94 & Omega;Maximum output level: +12dBuFrequency response 20-20kHz: +/-0.09dBDynamic range: 107.5dB typical (A-weighted)THD+N @ 1kHz: -101dB typical (un-weighted)PhonesOutput impedance: 10 & Omega;Maximum output level: +11.4dBuFrequency response 20-20kHz: +/-0.09dBDynamic range: 104dB typical (A-weighted)Power @ 33ohm: 137mWSupported Sample rates44.1kHz, 48kHz, 88.2 kHz, 96kHz, 176.4kHz, 192 kHz

Arturia Microfreak Experimental Hybrid Synth

MicroFreak EXPERIMENTAL HYBRID SYNTH A synthesizer like no other, MicroFreak is a peculiar, exceptional instrument that rewards the curious musician. It blends wavetable and digital oscillators with analog filters. It features a unique poly-aftertouch flat keyboard. It adds controlled randomness to sequences. This isn & rsquo;t a revolution, it & rsquo;s a mutiny. Whether you & rsquo;re looking for your first, affordable hardware synth or are a collector looking for original sounds and unique interface, MicroFreak is the synth you need. Small but fierce MicroFreak packs so much in to such a compact instrument, you & rsquo;ll wonder how we did it. We & rsquo;d love to say it was magic, but it was pure skill and passion. The best of both worlds Even though MicroFreak has a digital oscillator at its heart, & ldquo;opposites attract & rdquo; as the saying goes. That & rsquo;s why we & rsquo;ve included a lush-sounding analog filter. Product Description A synthesizer like no other, MicroFreak is a peculiar, exceptional instrument that rewards the curious musician. It blends wavetable and digital oscillators with analog filters. It features a unique poly-aftertouch flat keyboard. It adds controlled randomness to sequences. This isn & rsquo;t a revolution, it & rsquo;s a mutiny. This out-there little music machine features a versatile digital oscillator so you can create rare and interesting sounds with ease. Modes like Texturer, KarplusStrong, Harmonic OSC, and Superwave give adventurous musicians the chance to explore totally new, unheard possibilities. Like having dozens of synths in just one instrument, both wild-eyed newcomers and seasoned professionals will fall in love with MicroFreak & rsquo;s flexible, powerful synth engine. Physical modelling, wavetable synthesis, virtual analog, there is nothing as complete and exciting as the MicroFreak oscillator on the market. It's hard to believe from such a small synth, but here it is, ready for you to explore. Excite your creativity and reward your curiosity with a large, diverse sound palette. MicroFreak features 11 awesome oscillators, 4 bespoke Arturia engines, and 7 modes from our friends at Mutable Instruments. Inspired by the trailblazing 12-dB Oberheim SEM filter, you can make MicroFreak & rsquo;s filter scream or whisper to taste. The filter is state-variable, and can even auto-oscillate! You can use this is any way you like, from taking the edge of the razor-sharp wavetable sounds, or automating the cutoff by modulating it with keyboard pressure or the in-built sequencer. Record up to four automations, edit notes per step or use the innovative Spice and Dice sequencer functions to find happy accidents. Add randomization to create evolving, original patterns, and virtually rewire and reconfigure its signal chain and controls with the 5x7 modulation matrix.

Simple Studio Microphone Screen F2 Acoustically Designed Sound Absorbers

Pop filter Installable Microphone Housing Diameter: 45mm-60mm / 1.77-2.36 ''. Mic pop filter is a noise reduction cylinder designed and processed with high-quality noise reduction sponge. By absorbing and reflecting the surrounding noise through the noise reduction sponge, your microphone can be isolated in a quiet recording space, so that the microphone can specifically record your voice during recording and singing. The microphone pop filter can help you record a complete sound spectrum during the recording process and greatly reduce the external environmental noise. At the same time, microphone isolation shield also makes your recorded sound clear and pure. F2 wind and noise reduction screen can not only reduce the reflection of indoor recording sound, but also effectively reduce the interference of outdoor wind and environmental noise on human voice recording. This is a noise reduction cylinder designed and processed with high quality noise reduction sponge. The noise reduction sponge absorbs and reflects the surrounding noise, which can isolate your microphone in a quiet recording space, so that the microphone can specifically record your voice during the recording and singing process. It can help you record the complete sound spectrum and greatly reduce the external environmental noise during the recording process, and also make your recorded sound clear and pure. It can not only reduce the reflection of indoor recording sound but also effectively reduce the interference of outdoor wind and ambient noise on vocal recording. Reasons for choosing this product: 1. Optimize your voice to capture your pure human voice and reduce the interference of external voice to the recorded sound. 2. Reduce post-production sound trimming to reduce the need for redundant equalization and post-production. 3. A detachable blowout cover is designed in front of the integrated blowout cover to prevent the generation of plosive sounds and the erosion of the drool dialogue during the recording process. 4. Reduce ambient noise and sound reflections Isolate your microphone in a quiet recording environment while reducing sound reflections