High-speed Grinder
Plug In And Chink The Indicator Light,Open The Crushing Machine Cover,Nothing In The Grinding Slot. 2.Fasten Up The Cover ,Switch On And Make The Machine Idle For One Or Two Minutes,No Abnormal Phenomenon,Then Use It. 3.Power Cut,Open The Cover,Load The Materials,Don & rsquo;t Over The Maximum,Fasten Up The Cover,Plug In And Switch On,During The Operation,Crushing Sound From Noisy To Uniform, It Mains That Crushed Into Powder,You Can Turn It Off.General Materials Need Thirty Seconds And High Hardness Of Materials Need One Or Two Minutes,Boot Time Shall Not Exceed 8 Minutes At A Time. 4.Power Cut,Open The Cover,Clean Up The Grinding Slot. Notes: 1.It Is Suggested That The Materials Don & rsquo;t Exceed Two Thirds Of Crushing Slot 2.The Materials Must Be Dry,Should Not Be Wet.Something Have Water That Need To Dry Or In The Microwave Drying. 3.When You First Get Up,If The Material Is Meet By Blade,Make The Machine Can & rsquo;t Work,Please Power Cut Immediately,Prevents Motor Burn Out,Take Out The Foreign Body,Check The Fuse Is Good Or Bad And Restart. 4.During The Machine Working,Don & rsquo;t Open The Cover,Avoid To Cause Accidents,In The Case Of Open The Cover,Please don & rsquo;t Turn On ,Must Pull The Plug,Don & rsquo;t Use The Water Clean The Machine. 5.The Machine When Not In Use,Must Be Kept In Dry,Clean And Ventilated Place. 6.Before Using The Machine,Please Check:Screw Is Fixed And Rotation Of Blade Is Normal. 7.After Using For Long Time,If The Carbon Brush Wears Serious,It Need To Be Changed. 8.Product & rsquo;s Motor Belongs To Brush Motor,Boot A Spark,Carton Brush Wear Peculiar Smell,Belongs To The Normal Phenomenon 1.Plug In And Chink The Indicator Light,Open The Crushing Machine Cover,Nothing In The Grinding Slot. 2.Fasten Up The Cover ,Switch On And Make The Machine Idle For One Or Two Minutes,No Abnormal Phenomenon,Then Use It. 3.Power Cut,Open The Cover,Load The Materials,Don & rsquo;t Over The Maximum,Fasten Up The Cover,Plug In And Switch On,During The Operation,Crushing Sound From Noisy To Uniform, It Mains That Crushed Into Powder,You Can Turn It Off.General Materials Need Thirty Seconds And High Hardness Of Materials Need One Or Two Minutes,Boot Time Shall Not Exceed 8 Minutes At A Time. 4.Power Cut,Open The Cover,Clean Up The Grinding Slot. Notes: 1.It Is Suggested That The Materials Don & rsquo;t Exceed Two Thirds Of Crushing Slot 2.The Materials Must Be Dry,Should Not Be Wet.Something Have Water That Need To Dry Or In The Microwave Drying. 3.When You First Get Up,If The Material Is Meet By Blade,Make The Machine Can & rsquo;t Work,Please Power Cut Immediately,Prevents Motor Burn Out,Take Out The Foreign Body,Check The Fuse Is Good Or Bad And Restart. 4.During The Machine Working,Don & rsquo;t Open The Cover,Avoid To Cause Accidents,In The Case Of Open The Cover,Please don & rsquo;t Turn On ,Must Pull The Plug,Don & rsquo;t Use The Water Clean The Machine. 5.The Machine When Not In Use,Must Be Kept In Dry,Clean And Ventilated Place. 6.Before Using The Machine,Please Check:Screw Is Fixed And Rotation Of Blade Is Normal. 7.After Using For Long Time,If The Carbon Brush Wears Serious,It Need To Be Changed. 8.Product & rsquo;s Motor Belongs To Brush Motor,Boot A Spark,Carton Brush Wear Peculiar Smell,Belongs To The Normal Phenomenon
High-speed Grinder
₦ 163,350.00
₦ 165,000.00
-1%