Fluke 1507 Insulation Resistance Tester
1507 Insulation Resistance Tester Fluke insulation resistance testers are rugged, compact, reliable & ideal for troubleshooting, preventive maintenance applications. The insulation tester is compact, rugged, reliable, and easy to use. With its multiple test voltages, it is ideal for many troubleshooting, commissioning, and preventative maintenance applications. Additional features, like the remote probe on this tool, save both time and money when performing tests. Insulation test range - 0.01 megaohms to 10 gigaohms Insulation test voltages - 50 V, 100 V, 250 V, 500 V, 1000 V Live circuit detection prevents insulation test if voltage > 30 V is detected for added user protection Auto-discharge of capacitive voltage for added user protection AC/DC voltage: 0.1 V to 600 V 200 mA Continuity Resistance: 0.01 ohms to 20.00 kiloohms Save both time and money with automatic calculation of Polarization Index and Dielectric Absorption Ratio Insulation Testers: Readings You Can Trust Whether you work on motors, generators, cables, or switch gear, the Fluke Insulation Resistance Testers provide noise-free, reliable results. With advanced performance, the insulation tester line is designed to be safe, simple to use and gimmick-free. A perfect solution for troubleshooting, commissioning, and preventative maintenance applications.Safety Information Key FeaturesRugged, compact advanced insulation resistance tester for electrical contractors and industrial and commercial electriciansAutomatically calculates Polarization Index and Dielectric Absorption RatioMakes repetitive tests simple and easy with a Compare (Pass/Fail) function Offers multiple insulation test voltages: 50 V, 100 V, 250 V, 500 V, and 1000 V Repetitive or hard-to-reach testing is easy with the remote test probe Live circuit detection prevents insulation test if voltage greater than 30-Volts is detected for added user protection Read measurements easily with large, backlit display Save both time and money with automatic calculation of polarization index and dielectric absorption ratio Make repetitive tests simple and easy with the 1507's Compare (Pass/Fail) function Repetitive or hard-to-reach testing is easy with the remote test probe Live circuit detection prevents insulation test if voltage greater than 30-Volts is detected for added user protection Read measurements easily with large, backlit display
376 FC True RMS AC/DC Clamp Meter
advanced troubleshooting performance. The I flex flexible current Probe allows for easy measurement around wires in tight space in addition, all three clamps are now part of the Fluke Connect family of wireless test tools.Effortlessly log and trend measurements with this AC/DC clamp meter offering advanced troubleshooting performance and wireless transmission. Ideal for industrial and commercial applications, this clamp meter measures up to 1000 V AC/DC via a clamp, and the flexible current probe extends the current measurement to 2500 AFeatures* Voltage to 1000 V AC or DC* Resistance to 60 k & Omega; with continuity detection* Min, max, average, and inrush recording to capture variations automatically* Work safely and conveniently* The 376 FC clamp carries a CAT III 1000 V, CAT IV 600 V safety rating, designed to offer you the highest possible protection in a test tool.The flexible probe:* Expands the measurement range to 2500A AC* Allows frequency measurement to 500 Hz with body jaw and iFlexKey FeaturesiFlex™ flexible current probe expands the measurement range to 2500 A ac while providing increased display flexibility, ability to measure awkward sized conductors and improved wire accessCAT IV 600 V, CAT III 1000 V safety ratingIntegrated VFD low pass filter and state of the art signal processing allows for use in noisy electrical environments while providing stable readingsProprietary inrush measurement technology to filter out noise and capture motor starting current exactly as the circuit protection sees itErgonomic design fits in your hand and can be used while wearing personal protective equipmentLarge, easy to read, backlight display automatically sets the correct measurement range so you do not need to change switch positions while taking a measurementConnect your meter to your smartphone with Fluke Connect MeasurementsRead measurements on your phone at a safe distance, wearing less PPE while your meter takes all the risksRecord results directly to your phone and the CloudCapture intermittent faults while performing other tasks using the logging capabilitiesCreate and share reports from the field via email, or confer in real-time with ShareLive™ video callsLog and trend measurements to pinpoint intermittent faultsTransmit results wirelessly via Fluke Connect® Measurements app1000 A ac and dc current measurement with fixed jaw2500 A ac current measurement with iFlex™ flexible current probe1000 V ac and dc voltage measurementTrue Rms ac voltage and current for accurate measurements on non-linear signalsFrequency measurement to 500 Hz with both jaw and iFlex™60 k & Omega; resistance measurement with continuity detectionMin, max, average and inrush recording to capture variations automatically500 mV dc measurement range to interface with other accessories1000 µF capacitance measurementWhat's In the BoxWhat's included with the Fluke 376 FCClamp Meter18" iFlex® Flexible Current ProbeTL75 Test LeadsCarrying Case2 x AA Alkaline BatteriesCoated Instruction CardSafety Information Sheet
113 True RMS Utility Multimeter 3078875
The Fluke 113 True-RMS Utility Multimeter is a digital multimeter (also known as a multitester) that measures AC/DC voltage to 600V, resistance to 60 kiloohms, and capacitance to 9,999 microfarads. The meter has a diode check for testing general-purpose germanium, silicon, and power diodes, and a continuity beeper which provides audible detection of resistance by turning on at less than 25 ohms and off at 250 ohms. It is also able to simultaneously check for voltage and continuity. This true RMS meter provides accurate readings when measuring linear or nonlinear loads where the current or voltage has a sinusoidal or non-sinusoidal waveform and has both manual- and auto-ranging capabilities for user flexibility. A Max/Min function records signal fluctuations and a hold function freezes measurements on the display. The 6000-count resolution, 3-1/2 digit digital display is backlit for readability in low-light conditions. The meter is safety rated for Category III to 600V and Category IV to 300V. It uses a 9V battery (installed) with a battery life of approximately 300 hours without backlight and has a sleep mode to maximize battery life. The meter measures 6.58 x 3.35 x 1.81 inches (H x W x D) and weighs 13 oz. /404 g. (H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.) This meter includes a holster with built-in probe holders for convenient storage. Multimeters are electrical test meters that measure multiple properties of an electrical circuit, such as current, voltage, resistance, capacitance, and continuity. Available in handheld or benchtop models, multimeters diagnose electrical problems in electrical equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Multimeters display information either in analog or digital form. Factors that influence meter choice include the electrical properties to be measured, the anticipated range of results, and the desired level of protection against transient voltage. Safety ratings are based on International Electro technical Commission (IEC) standards for low-voltage test equipment. IEC 61010 delineates four overvoltage installation categories. In general, a meter with a category IV rating will provide more protection against transient voltages than a meter with a lower category rating. Fluke Corporation manufactures electrical testing tools and software for industrial and commercial applications.Manufacture: FlukeProduct Description: UTILITY MULTIMETERThe Fluke 113 Digital Multimeter gives users the means to quickly and easily do basic meter set and reconnect testing. This meter is simple-to-use and has the features needed to repair most electrical problems. The Fluke 113 has significant improvements over other digital multimeters available on the market, including Fluke model 7-600. Using the Fluke VCHEK LoZ low impedance measurement function, users can simultaneously test for voltage or continuity. The Min/Max function lets you record signal fluctuations. The Fluke 113 can perform diode tests, and also provides both auto and manual ranging capabilities. With features such as conformance to the latest safety standards, backlight, and a much larger display thats easier to view, this meter is a must have for every toolbox.True-rms ac voltage and current for accurate measurements on non-linear signalsMeasure up to 1000 V ac and dcMeasure up to 10 A (20 A for 30 seconds)10,000 microF capacitance rangeFrequency to 50 kHzBuilt in thermometer conveniently allows you to take temperature readings without having to carry a separate instrumentResistance, continuity and diode testLow power wireless technology allows the display to be carried up to 10 meters (33 ft) away from the point of measurement for added flexibility.No interference with measurementsThe removable magnetic display can be conveniently mounted where it is easily seenMake measurements without holding the meter to improve visual focus on probes and augment safe electrical measurementsUse as a conventional multimeter when the display is connectedRadio transmitter automatically turns off when the display is connected to the meterAuto power off maximizes battery lifeMin/Max and Average recording to capture variations automaticallyTest continuity and diodesEasy to read display with large digits and bright backlightBattery life approximately 400 hoursKey FeaturesDigital multimeter measures AC/DC voltage, resistance, and capacitance and performs continuity and diode tests True RMS meter provides accurate readings when measuring linear or nonlinear loads where the current or voltage has a sinusoidal or non-sinusoidal waveform Simultaneously checks for voltage and continuity Manual and auto ranging modes for user flexibility Safety rated for Category III to 600Volts and Category IV to 300 Volts
