3.7V Rechargeable Electric Heated Insoles Warm Sock Winter Heater Pad W/Remote 41-46
Specifications: Electrical : Insole voltage: 3.7V Insole capacity: 1800mA Operating voltage range: 3.0V-4.2V Charge cut-off voltage: 4.2V Discharge cut-off voltage: 3.0V life: 500 cycles or more Type: Full Foot : 35-40/41~46 Material: Osley Charger : Charging mode: constant current and constant voltage (CC/CV) Charging temperature: 0 ° ~ 45 ° Input: AC/100-230V 40-60Hz Output: /4.2V 500mA*2 Fever : After booting up to 60 ° , the use time is about 3-4 hours. The mid-range can reach 55 ° , and the use time is about 4-5 hours. Low gear up to 50 ° , use time is about 6-7 hours Instructions: 1. Please fully charge the before using this product. Plug in the charger, the charger lights red, indicating that the is charging. When the is fully charged, the charger lights up green and the is fully charged. 2. After the is fully charged, press the H button of the remote control, the LED of the remote control flashes once, the 3 LEDs of the insole are illuminated for 3 seconds, and the insole works in the high-grade mode. 3. Press the remote control M button, the remote control LED flashes once, the insole 2 LEDs are on for 3 seconds, and the insole works in the mid-range mode. 4. Press the remote control L button, the remote control LED flashes once, the insole 1 LED is on for 3 seconds, and the insole works in the low mode. 5. Press the remote control to open the key, the remote control LED flashes once, the insole LED goes out, and the insole stops working. If the remote control is accidentally lost, use the switch to the insole charging port to control it. 1, long press the insole to open the key for 3 seconds to start, the insole 3 LEDs for 3 seconds, the insole works in high-end mode. 2. After the insole is turned on, press the key again, the insole 2 LEDs are on for 3 seconds, and the insole works in the mid-range mode. 3, press the key again, the insole 1 LED is on for 3 seconds, and the insole works in the low mode. 4, press the key again, the insole is cycled in the high-end mode, repeated cycles. 5, long press the insole to open the key for 3 seconds to shut down, the LED goes out, the insole stops working. Precautions: 1. The internal electronic control system uses high-frequency dual- radio frequency control to ensure the consistency, stability and aesthetics of the remote control. 2. Different buttons of the remote control control different working modes. 3. The heating material is made of composite carbon fiber material, which has the characteristics of high heat generation efficiency and strong strength. When the carbon fiber material is energized and heated, it can radiate infrared rays and promote health effects such as circulation. 4. The is made of high-capacity high-capacity polymer batteries to ensure the longest service life while maintaining warmth. 5. Due to the use of high-strength, high-softness composite carbon fiber as the heating , the problem that the conventional heat-generating insole repeatedly bends and damages the heating while walking is avoided. It has the functions of convenient warmth, high heat generation and strong heat preservation performance. Package Included: 2 x Shoes Pad 1 x USB Cable 1 x Remote Control Notes: 1. After receiving the insole, don't cut it at will, please according to your size and using tne size card to cut it to your corresponding size. 2. Manual measurement, please allow 1-2mm error, thank you. a a a a a Key FeaturesEasy to useExquisite WorkmanshipWell MadeBest Choice and best discountsCustomer Care is Our Top PriorityOffer is Subject to AvailabilityBig SaleWhat's In the Box2 x Shoes Pad 1 x USB Cable 1 x Remote Control