Battery Balancer Equalizer 24vA
24v battery equalizerThis is an active transfer battery EqualizerWhen two or more batteries connected in series or parallel charge and discharge, voltage differences begin to occur.while some batteries are overcharged, others may be undercharged.battery equalizer will equalize/balance the battery voltage when it detect there are 20mv between two batteries. It will shunt current from one battery(the higher voltage one) to the other battery(the lower voltage one) until their battery voltage almost becomes same.Parameters Working Voltage -12v-24vWorking Current - 0-10AStandby Current - less than 5mAWorking Temperature -29 to 60⁰cReverse Voltage ProtectionRecommended for 2v 6v 12v lead acid batteries, lithium Polymer packs, LifePo4 packs, solar batteriesThis will improve battery's performance and extend battery's lifetime by at least additional 2 yrsThis battery Equalizer Balancer can be used for multiple batteries in series or parallel once it's voltage is 24VParameters Working Voltage -12v-24vWorking Current - 0-10AStandby Current - less than 5mAWorking Temperature -29 to 60⁰cReverse Voltage ProtectionWhat's In the Box1 X 24v Battery EqualizerManual
Energy Power Meter Ammeter/Wattmeter 80A 17KW
Energy Power Consumption Meter 80A 17KW Din Rail0-80A DDS1897 LCD Digital Display Single Phase Electronic Energy KWh Meter Features:1. 35mm DIN Rail mounting meets the standards of DIN EN50022.2. 17.5mm pole width meets the standards of DIN43880.3. LCD backlight digital display, no reset button, to avoid human manipulation with the data.4. It displays energy, voltage, current ,power.5. Red LED energy pulse signal.6. Embedded end cover, ensuring power supply safety.7. With the features of good reliability, small size, light weight, beautiful appearance and easy installation.8. Adopt microelectronics and digital processing technology to measure electric energy, accurate and reliable.9. Large scale integrated circuits and precision SMT technology, with good electromagnetic interference resistance and stable performance.Specification:Material: PlasticModel: DDS1897Accuracy: First GradeReference Voltage: 220V/230V 50/60HzReference Current (Max. Current): 5(80)AInsulating Property: 1min 4KV Alternating Voltage, 1.2/50us 6KV Waveform Impulse VoltageDisplay: LCD Backlight / LCD DisplayInstallation: 35mm DIN RailWiring Method: Up-out and down-in/up-in and down-outPower: 17000WEnvironment Temperature: -20C~+50CPole Width: 17.5mm/0.7inFunctions: Display electricity, voltage, current, frequency, power factorsPackage Size: Approx. 8.6 * 4.2 * 7.2cm/3.4 * 1.7 * 2.8inVoltage :140-250VACCurrent: 0.1-80AEnergy: 0.1-99999.9 KWHPower: 0.1-17000WWhat's In the Box1*80A WattmeterManual
DC Battery Monitor Meter/Voltmeter/Wattmeter 150A
FeaturesMeasures DC Amps, Amp-hours, Watthours, Volts and Watts of solar batteries, check inverter load input and total solar panel production. It can also be used to check the individual solar panel output before installation. See other uses below. Note that to test solar panels, the output terminals must be connected to load like battery or solar charge controller KINDLY NOTE THAT THE OUTPUT TERMINALS MUST BE SEPARATED AND NEVER TOUCH EACH OTHERCaptures peak current, peak power, and minimum voltage (voltage sag) lasting a fraction of a second.Rare combination of Voltmeter, DC Amp meter & Amp hour counting, Watthour and power analyzer features. Measures wide range of values not normally found on multimeters or low cost test equipmentPowered by the measured circuit or connect an auxiliary battery or DC power source to provided 3-pin socketReverse connection protectionPowerful, 8 MIPS micro-controllerUses very low resistance (0.001 Ohm) shunt in negative (black wires) leadsSmall size and lightweightTo measure solar panel output, connect the output terminal to a batteryIt can also be used to monitor inverter DC load on the batteries. It can also be used to measure input and/or output of solar charge controller. You can connect it in between the solar panels and solar charge controller to monitor solar panel output into the charge controller. If you want to monitor charging output of the solar charge controller, connect it in between the solar charge controller and the batteriesFull user's manual includes electrical tutorialExample applicationsRV battery monitor and battery chargersMarine battery monitor and battery chargersGolf cart batteries and chargersDigital panel meter AmmeterSolar Panel output Wheelchair batteries and chargersSolar Power batteries and chargersWind Power generators, batteries and chargersElectroplating and metal plating Amp Hour measurementHam Radio & Amateur Radio base station equipment, battery monitoring and chargersElectric bike batteries and chargersMeasurement Parameters Voltage Range 6-60V♦ Measure 0-150a.resolution 0.01A0-60V.resolution 0.01V0-6554W.resolution 0.1W0-65AH.resolution 0.001Ah0-6554WH.resolution 0.1WhWhat's In the Box1 DC MeterManual
